A pump with a required manometric pressure of 12 m gives a flow rate of 7500 liters/minuteit is designed. The rotation speed of the pump shaft is 1800 RPM according to this pumpdimensionless pump specific velocity which of the following options?Formulas,L Vav?+a+ +hpompas=P2+ #25++hearbing + h tonten Re .V.D6.9a -1.8 lophg yeretheneplem= hgatrekti + hxyeret1pompaenpy=(4++),pmpa girişiO 2.541O 0,965O 1,865O 1,025O 0,678O O O O

Name: A pump with a required manometric pressure of 12 m gives a flow rate
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: A pump with a required manometric pressure of 12 m gives a flow rate of 7500 liters/minuteit is designed. The rotation speed of the pump shaft is 1800 RPM according to this pumpdimensionless pump specific velocity which of the following options?Form

Given: Required pressure = 12m; Flow rate = 7500 litres/ minute

Science

Physics

A pump with a required manometric pressure of 12 m gives a flow rate of 7500 Rersiminute tis designed. The rotation speed of the pump shaft is 1800 RPM according to this pump dimensionless pump specific velocity which of te folowing options? Formulas. heneplem enpy=(4++) 2541 1865 1025 O 0678

A pump with a required manometric pressure of 12 m gives a flow rate of 7500 Rersiminute tis designed. The rotation speed of the pump shaft is 1800 RPM according to this pump dimensionless pump specific velocity which of te folowing options? Formulas. heneplem enpy=(4++) 2541 1865 1025 O 0678

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 115AP: A sump pump (used to drain water from be basement of houses built below the water table) is draining...

See similar textbooks

Similar questions

Water is moving at a velocity of 2.00 m/s through a hose with internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
An oil gusher shoots crude 25.0 m the through a pipe with a 0.100-m diameter. Neglecting resistance but not resistance of the pipe, and assuming laminar flow, calculate pressure at be entrance of be 50.0-m-Iong vertical pipe. Take of the oil to be 900 kg/m3 and its viscosity to be 100(N/m2) s (or 1.00 Pa s). Note that you must take into account the pressure due to 50.0-m column of oil in pipe.
A sump pump (used to drain water from be basement of houses built below the water table) is draining a flooded basement at rate of 0.750 L/S, with an output pressure of 3.00105N/m2 . (a) The water enters a hose with a 3.00-cm inside diameter and rises 2.50 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.500 m in height and widens to 4.00 cm in diameter. What is the pressure now? You may neglect frictional losses both parts of the problem.
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.
What is the difference between flow rate and fluid velocity? How are they related?
(a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
Water is moving at a velocity of 2.00 m/s through a hose with an internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
A fire hose has an inside diameter of 6.40 cm. Suppose such a hose caries a flow of 40.0 L/s starting at a gauge pressure of 1.62106 N/m2. The hose goes 10.0 m up a ladder to a nozzle having an inside diameter of 3.00 cm. Calculate the Reynolds numbers for flow in the fire hose and nozzle to show that flow in each must be turbulent.
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
A small artery has a length of 1.1103m and a radius of 2.55105m . If the pressure drop across the artery is 1.3 kPa, what is the flow rate through artery? (Assume Eat the temperature 37°C)