A pump with an impeller diameter of 0.02 m, an impeller speed of 58.3 rpm, a total capacity of 12 L/s, an available head of 70 m, and a brakepower of 12 kW is used to pump water. Determine the capacity of a homologous pump with twice the impeller diameter and operating at half the speed. 60 L/s 36 L/s O48 L/S 72 L/s

A pump with an impeller diameter of 0.02 m, an impeller speed of 58.3 rpm, a total capacity of 12 L/s, an available head of 70 m, and a brakepower of 12 kW is used to pump water. Determine the capacity of a homologous pump with twice the impeller diameter and operating at half the speed. 60 L/s 36 L/s O48 L/S 72 L/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump pumps water at a flow rate of 7 m³/s to a height of 10 m. If the pump works at the best efficiency point, find the pump impeller diameter, pump speed, the best efficiency value of the pump, the head at the best efficiency value, and the specific speed of the pump, given that CQ=0.15 CH=6 CP=0.75.
A pump with an impeller diameter of 0.02 m, an impeller speed of 58.3 rpm, a * total capacity of 12 L/s, an available head of 70 m, and a brake power of 12 kW is used to pump water. Determine the capacity of a homologous pump with twice the impeller diameter and operating at half the speed. Choices: A.60L/S B.36 L/S C.48 L/S D.72L/S
The net head delivered by a pump at a rotational speed of 1000 rpm is 10 m. If the rotational speed is doubled, the net head delivered will be (a) 5 m (b) 10 m (c) 20 m (d ) 40 m (e) 80 m
PAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answer
A pump rated at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, how much electricity is required to keep the process running for 24 hours? Choices: A. 29.37 kWh B. 35.28 kWh C. 56.71 kWh D. 43.21 kWh
1) Interpret solar power in the context of environmental impact.2. What is the rigid dichotomy between windmill and diesel-driven pumps?3. For a normal windmill-driven pump at 3 m/s wind speed, the yield at a 10 m Head is typically 0.12 liters/s per m2 of rotor area, value windmills in the context of yield.
A pump is designed to deliver 9500 L/min of water at a required head of 8 m. The pump shaft rotates at 1100 rpm. The pump specific speed in nondimensional form is (a) 0.277 (b) 0.515 (c) 1.17 (d ) 1.42 (e) 1.88
A double-acting single cylinder reciprocating pump has 150 mm piston diameter and 300 mm stroke length, running with 30 r.p.m. Determine, work done in N/ms at maximum head against which the pump has to work. Consider suction head 4.5 m, delivery head 32 m, friction head 0.578 m at middle of suction stroke and 3.47 m at middle of delivery stroke. Acceleration head during end of suction stroke -3.62 m and beginning of suction stroke 3.62 m. Acceleration head during beginning of delivery stroke 21.69 m and end of delivery stroke -21.69 m.
A small centrifugal pump, when tested at N = 2875rpm with water, delivered Q = 252 gpm and H = 42 meters at its best efficiency point of 76%. Determine the specific speed of the pump and the required power input to the pump.
The impeller of a centrifugal pump has inner and outer diameters of 13 and 30 cm, respectively, and a flow rate of 0.15 m3/s at a rotational speed of 1200 rpm. The blade width of the impeller is 8 cm at the inlet and 3.5 cm at the outlet. If water enters the impeller in the radial direction and exits at an angle of 60° from the radial direction, determine the minimum power requirement for the pump
A double-acting single cylinder reciprocating pump has 150 mm piston diameter and 300 mm stroke length, running with 30 r.p.m. Determine, maximum head against which the pump has to work. Consider suction head 4.5 m, delivery head 32 m, friction head 0.578 m at middle of suction stroke and 3.47 m at middle of delivery stroke. Acceleration head during end of suction stroke -3.62 m and beginning of suction stroke 3.62 m. Acceleration head during beginning of delivery stroke 21.69 m and end of delivery stroke -21.69 m.
A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radialat the inlet of the rotor. The pump has the following characteristics:Flow rate Q = 72 L/sInlet diameter D1 = 90 mmOutlet diameter D2 = 280 mmHead H = 25mWidth at the inlet b1 =20 mmWidth at the outlet b2 = 18 mmLeakage q = 2 L/sMechanical loss Pm = 1.41 kWBlade angle at the outlet β2 = 35ͦThe water density ?=998 ??/m^3Atmospheric pressure 101 kPa1) Draw the velocity triangles at the inlet and the exit of the impeller.2) Determine the magnitude of the absolute velocity of the flow (?) and the impeller velocity(U) at the inlet and outlet3) Determine the blade angle at the inlet.4) Determine the hydraulic, mechanical and volumetric efficiencies.5) Determine the minimum number of blades required for the slip to not exceed 0.9.6) Determine the static pressure difference (P2-P1) through the impeller by using Bernoulliequation.7) Determine the available NPSH if the pump is placed 2m above the…