a R₁ C R₂ L b Fig. 1. RLC circuit. R1 = 100 2, R2 = 57 02, L = 39 mH, C = 2.2 µF. [1] 1. Redraw this circuit, replacing each component with its equivalent impedance in the phasor domain. 2. Simplify the circuit to a single impedance between nodes a and b, looking for series and parallel impedance combinations you can simplify. Express the result as a magnitude in ohms and a phase angle. 3. Find the input impedance for frequencies of 100, 500, 1000, and 2000 Hz. Express each result as a magnitude and a phase angle.

a R₁ C R₂ L b Fig. 1. RLC circuit. R1 = 100 2, R2 = 57 02, L = 39 mH, C = 2.2 µF. [1] 1. Redraw this circuit, replacing each component with its equivalent impedance in the phasor domain. 2. Simplify the circuit to a single impedance between nodes a and b, looking for series and parallel impedance combinations you can simplify. Express the result as a magnitude in ohms and a phase angle. 3. Find the input impedance for frequencies of 100, 500, 1000, and 2000 Hz. Express each result as a magnitude and a phase angle.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A source of angular frequency 1 rad/sec has a source impedance consisting of 1ohms resistance in series with 1 H inductance. The load that will obtain the maximum power transfer is __________. Group of answer choices 1ohms resistance in series with 1 F capacitor 1ohms resistance in parallel with 1 H inductance 1ohms resistance 1ohms resistance in parallel with 1 F capacitor
3. PLEASE SOLVE AND SHOW YOUR DETAILED SOLUTION WITH FBD. Calculate the equivalent impedance of a circuit in which a coil of wire having a value of 6.5 Ω ∠54∘ is connected parallel with a capacitive reactance of 7.25 ohms.
Short Problem: Given a parallel RLC circuit comprised of the following element: 97.19-ohm resistor, ideal inductor with reactance of 36.14 ohms; and a capacitor with reactance of 16.25 ohms. Compute for true power in watts given an ac voltage source of 100 cis 0 volts. Note: Follow this reminder carefully. Compute to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer.
1 A circuit having a resistance of 12Ω, an inductance of 0.15 H and a capacitance of 100μf in series is connectedacross a 100V, 50Hz supply. Calculate the impedance, current, the phase difference between the current andsupply voltage. 2. Two circuits with impedances of Z1 = 10 + j15Ω and Z2 = 6 – j8Ω are connected in parallel. If the supply current is 20A, what is the power dissipated in each branch?
write the complete solution asap
Short Problem: Given a parallel RLC circuit comprised of the following element: 57.81-ohm resistor, ideal inductor with reactance of 65.75 ohms; and a capacitor with reactance of 6.59 ohms. Compute for true power in watts given an ac voltage source of 100 cis 0 volts.
COURSE: Electrical EngineeringSUBJECT: Electrical ApparatusINSTRUCTIONS:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units• Round up to 3 three decimal places the FINAL ANSWERS and BOX it. PROBLEM:A capacitor in series with a 66 Ω resistor is connected to a 120 V, 60 Hz source. If the impedance of the circuit is 116 Ω, determine the size of the capacitor.
Short Problem: Given a parallel RLC circuit comprised of the following element: 62.52-ohm resistor, ideal inductor with reactance of 33.15 ohms; and a capacitor with reactance of 6.11 ohms. Compute for true power in watts given an ac voltage source of 100 cis 0 volts. PLEASE ANSWER WITHIN 30 MINUTES. Round off to the nearest 4 decimal places. No Scientific notation. Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed.
Electrical Engineering A cylindrical hollow pipe is made of steel (μr = 180 and σ = 4 x10^6 S/m).The external and internal radii are 7 mm and 5 mm. The length of the tube is 75 m.The total current I(t) flowing through the pipe is:I(t)= 8 cos(ωt) with ω=1200π rad/sDetermine:d) The intrinsic impedance of the good conductor. Remember that: Transcribed Image Text:η = = √2/45° σ·δ
Show that at a given frequency ω, the circuits will have the same impedance between the terminals a,b ifR1=R21+ω2R22C22,C1=1+ω2R22C22ω2R22C2.2. Find the values of resistance and capacitance that when connectedin series will have the same impedance at 40 krad/s as that of a1000 Ω resistor connected in parallel with a 50 nF capacitor.
Convert the lower part of the circuit shown in fig. 1 into Wye (Ra, Rb & Rc) then find Rt, (Series current) Is1, Is2, V3, V1 V2, & IT
a series r-c circuit takes a current whose equation is i=0.85sin(754t+pi/4) when connected to a source of emf having the equation e=340sin754t. calculate the capacitance of the capacitor, circuit power factor, and power.