A rankine cycle operates between a pressure limit of 6 MPa. and 50 kPa., the steam leaves the boiler at 450 C, the isentropic efficiency of the turbine is 94%, the steam mass flow rate is 20kg/sec. draw the T-S diagram assuming point 1 is at the pumpe entrance. and determine the required power to operate the pump, cycle thermal efficiency. Ans. (122 kW, 30.25%)

A rankine cycle operates between a pressure limit of 6 MPa. and 50 kPa., the steam leaves the boiler at 450 C, the isentropic efficiency of the turbine is 94%, the steam mass flow rate is 20kg/sec. draw the T-S diagram assuming point 1 is at the pumpe entrance. and determine the required power to operate the pump, cycle thermal efficiency. Ans. (122 kW, 30.25%)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. If the efficiency at high – pressure and low – pressure turbine is 76% and 75%, determine the cycle efficiency, in percent.
1. A reheat cycle with two stages of reheating is executed with steamexpanding initially from 90 bar and 530°C. The two reheaterpressures are 10 bar and 0.6 bar, and the steam leaves eachreheater at 480°C.Condensation occurs at 0.03 bar. Find the cycleefficiency.2. An ideal reheat turbine with one stage of reheat receives steam at8.0 MPa and 480°C. Reheat pressure is 0.83 MPa and exhaustpressure is 0.007MPa. The work is 1559 KJ/kg and thermalefficiency is 41%. Find the temperature of the steam leaving thereheater.
Steam at 6.155MPa and 435degC enters the turbine of a power plant which operates on actual vaport power cycle. The pressure at the exit of the turbine is 418 kPa, and steam leaves the condenser as a saturated liquid at 62degC. The pressure is increased to 12.2 MPa accross the pump. The turbine and pump have isentropic efficiencies of 82% and 74% respectively. For this cycle, determine th: a. Wnet per unit mass of steam flow and the heat transfer to steam passing through the boiler (kj/kg)b. thermal efficiency (%) c. heat transfer to colling water passing the condenser (kj/kg of steam condensed)
6. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the thermal efficiency of the cycle in %? A. 25% C. 15% B. 26% D. 16%
In an ideal Rankine cycle, steam generated at 3.546 Mpa and 450°C. The condenser isat 45°C. Determine (a) the ideal pump work, (b) the cycle efficiency, (c) for an enginewith the same end state, determine the engine efficiency.(Note: Draw the schematic and T-s diagram)
Water is the working fluid in a Rankine cycle with reheat. Superheated vapor enters the turbine at 10 MPa, 480°C, and the condenser pressure is 6 kPa. Steam expands through the first-stage turbine to 0.7 MPa and then is reheated to 480°C. The pump and each turbine stage have an isentropic efficiency of 70%.Determine for the cycle:(a) the total heat addition, in kJ per kg of steam entering the turbine.(b) the percent thermal efficiency.(c) the magnitude of the heat transfer from the working fluid passing through the condenser to the cooling water, in kJ per kg of steam entering the first-stage turbine.
A simple non-ideal saturated Rankine cycle turbine receives 125 kg/s of steam at 300oC andcondenses at 40oC. This cycle has turbine and pump polytropic efficiencies of 0.88 and 0.75respectively, and a total pressure drop in the feed-water line and steam generator of 10 bar.Calculate:a) The net cycle power, in megawatts. b) The cycle efficiency.
If a 2 kg's of steam is being circulated in a Rankine cycle, with one extraction for regenerative feed. steam leaves the boiler and enters the turbine at 4.25 MP, 500°C and exhausts as dry and saturated at 0.1 MPa, In the turbine, steam bled or 700 Ps. (a)What is the mass of bied steam? (b)What is the total turbine output based on the properties given? (c)What is the work input to low pressure pump? (d)what is the efficiency of the cycle? (e)what is internal efficiency of low-pressure turbine considering 100% to the high pressure turbine?
an ideal reheat turbine with one stage of reheat receieves steam at 8 mpa, 480 degrees celsius. reheat pressureis 0.83 mpa and exhaust pressure is 0.0007 mpa. determine A) heat added B) effeciency cycle C) energy chargable D) engine thermal effeciency
1. A reheat steam cycle has 13.65 MPa pressure at the high pressure turbine inlet and a 2500 kPareheat pressure, the temperature at the inlet of the high pressure turbine and reheattemperature of the steam is 540 0C, condenser pressure is 3.4 kPa, engine efficiency of highpressure and low pressure turbine are both 75 %. Sketch the cycle lay out and cycle T-s diagram.a. Find the enthalpy at each state point. (Summarize)b. Find the actual enthalpy at the exit of the high-pressure turbine and low-pressure turbine.c. Find the cycle thermal efficiencyd. If the net power at the turbine is 100 MW find the mass flow rate of steam, in kg/s;e. Heat rejected by the condenser, in MW
A rankine cycle has the following operation conditions:Steam pressure, 2.5 mpaSteam temperature, 280CExhaust pressure, 0.026mpaIndicated steam rate, 5.45 kg/kwhMechanical efficiency, 90% For ideal cycle and engine, calculatea) the thermal efficiency b) the engine steam ratec) the actual condition of exhaust steamd) the steam flow rate in kg/hr. for 1MW generator output at 94% efficiency
3. A 200 MW power plant operates on a simple Rankine cycle. Steam at 5.2 MPa, 400ºC expandsin a Rankine turbine to 0.036 MPa. Assume actual turbine with isentropic efficiency of 75 % forboth the compressor and expander. 3.1 Heat added in steam Generator , KW 3.2 Power loss at Turbine, KW 3.3 Actual thermal efficiency of the cycle 3.4 Mass of water in kilogram needed for an hour in the condenser if the changeof temperature for the water is 27ºF