A reaction turbine has guide vanes at an angle of 30° and the runner blades make an angle of 80° relative to the tangent at inlet. The blades width at the inlet is 14 of the outer diameter. The water does not have any tangential velocity at the outlet. The head is 25 m and the rotational speed of the runner is 16.67 rotations per second. The turbine efficiency is 88 %. Determine the turbine runner diameter at the inlet and the power developed. T

A reaction turbine has guide vanes at an angle of 30° and the runner blades make an angle of 80° relative to the tangent at inlet. The blades width at the inlet is 14 of the outer diameter. The water does not have any tangential velocity at the outlet. The head is 25 m and the rotational speed of the runner is 16.67 rotations per second. The turbine efficiency is 88 %. Determine the turbine runner diameter at the inlet and the power developed. T

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

A Pelton wheel is to be designed for a head of 400 m when running at 500 rpm. The Pelton wheel develops 10000kW shaft power. The blade angle at outlet is 15º. The relative velocity of water is reduced by 5% by moving over the buckets. Velocity of the buckets = 0.45 times the velocity of the jet, overall efficiency = 0.8 and coefficient of the velocity = 0.98. If the Pelton wheel is provided with three nozzle, find (i) The diameter of jet (ii) Total flow rate and the force exerted by a jet on the buckets
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaftis running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.
A Pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400 m. The nozzle diameter is 160 mm and the coefficient of velocity is 0.98, The diameter of the wheel bucket circle is 1.75 m and the buckets deflect the jet by 150°. The wheel-to-jet speed ratio is 0.45. Neglecting riction, calculate (1) the power developed by the turbine, (i) its speed and (i) hydraulic efficiency.
A Kaplan turbine working under a head of 43 m deve-lops 15,400 B.H.P. The dia of theboss is 0"3 times the dia ofrunner. Determine the speed and dia of runner, if speed ratio is2, flow ratio as 0-65 and overall efficiency as 91%.
Before solve the problem please understand the question. Give me right solution according to the question. A flow rate of 0.14 m3 / s is required from a centrifugal pump with an outer radius of 23cm and rotating at 900 rpm. The width of the propeller is b = 8cm (at the outlet). Assuming 73% efficiency, what motor horsepower is required if the outlet angle is 165º? Suppose the pallets occupy 5% of the exit area.
In a francis turbine the vane angle at the entry to the runner is 90degrees, which is rotationg at 75rpm, outer radius is 0.6m and inner radius is 0.3m, velocity at entry and exit to the vanes is 1.8m/s. The water is discharged radially. If the discharge is 1.42m3/s and neglecting friction in the runner calculate: the vane angle at discharge the ouput power developed
It is desired to develop a 5 MW turbine under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head.(b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A Francis turbine develops 3 MW under a head of 50 m at an overall efficiency of 88%. The diameterof the runner at the inlet is 80 cm and runner rotates with 300 rpm. If hydraulic efficiency of the turbine is90% and runner height at the inlet is 10cm, calculate (a) guide vane angle at inlet (b) blade angle at inletand (c) degree of reaction of the turbine.
Water (density 1000=kg/m3) enters radially through a centrifugal pump whose impeller diameter has a diameter of 30 cm and breadth of 15 cm, the corresponding dimentions at the outer periphery are 60cm and 7.5 cm respectively. the blate angle at the outlet is 30 degree and the discharge is 225 lit/sec. the rotational speed of the impeller is 1200 rpm and the pump delivers water at a height of 115 m. if the overall and volumetric officiencies are 65% and 95% respectively, calcuate the theoretical head developed, mechanical efficiency and vane and blade angles at the inlet.
A pump has a suction condition of 50mm Hg vacuum pressure, 100mm diameter pipe and discharged condition of 250kpa at, 90mm diameter. The discharge tank is 50m elevation and the suction is 5m below the pump center line. If the discharge is 0.20 m3/s, find the pump efficiency for 260kw brake power. Answer: 74.32%
Some engineers are evaluating potential sites for a small hydroelectric dam. At one such site, the gross head is 340 m, and they estimate that the volume flow rate of water through each turbine would be 0.95 m3 /s. Estimate the ideal power production per turbine in MW.