A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. Determine the magnitude of the member CD. Is the member in tension or compression? Determine the support reactions at A. Determine the unstretched length of the spring EF given a spring constant of 150 kN/m.

Q: 2. Tid the percentage mercase in specu, in the Danis rise by 20 min. [Alls. 370] A Porter governor…

A: Ball 1 mass, m=3 kg Ball 2 mass, M=15 kg Arm length, BP=BD=200mm =0.2m Minimum radius of rotation,…

Q: Q2. For a closed end cylinder where the inner diameter is 80 cm and outer diameter is 86 cm, and the…

A:

Q: A circular rigid disk of mass m kg and radius rm is stationary at the top of a fixed sphere of…

A: Given: Disk mass - mDisk radius - rSphere radius - 2r To find: Angle θ at which the disk leaves the…

Q: 7. If a particle is connected to a spring, the elastic spring force is expressed by the equation F =…

A: Given: The elastic spring force, F=k s   Find: s means

Q: -. If the block at C is moving downward at 4 m/s, letermine the angular velocity of bar AB at the…

A:

Q: For the system shown in the figure, and y denote the absolute displacements of the mass m and the…

A: Dear Students

Q: Learning Goal: To calculate the maximum allowable stresses in pressure vessels, compute the minimum…

A:

Q: The allowable shearing stress is 105 MPa in the steel rod AB and 55 MPa in the brass rod BC. Knowing…

A: The allowable torque TA. Given: The allowable shearing stress in the steel rod AB is τAB=105 MPa.…

Q: For the circular shaft (G=12×106 psi) shown below: a. Compute the reaction torque and draw the…

A: According to the given data Segment  Diameter(in) Hollow diameter(in) Length(in) G(psi AB 6 4…

Q: From a state defined 300 psia, 100 cu. ft and 245 deg. F, Helium undergoes an Isentropic process to…

A: According to the given data P1=300Psia V1=100ft3 T1=245°F=705°R P2=0.5psig=14.7+0.5=15.2psia…

Q: 6-2) Determine the force P for impending sliding motion of the wedge to the left if the angle of…

A: Hi,     As per the guidelines, we can provide only typed solution not the handwritten solution. So,…

Q: 1) In the figure which shows a beam, its loading, and its rectangular cross-section, determine (a)…

A:

Q: 4. During a cold winter day, wind blows parallel to a 4 m high and 10 m long wall of a house. If the…

A:

Q: 1) The 1.62-oz golf ball is struck by the five-iron and acquires the velocity shown in a time period…

A:

Q: The 52 kg block is hoisted up the incline using the cable and motor arrangement shown. (Figure 1)…

A:

Q: 3. The rigid body shown below can be represented by a thin circular disk with a square hole in its…

A: According to the given data The density of the material=0.03028slugs/in3 The thickness of…

Q: Problem 23.2 For a piston cylinder system where the air inside the piston begins with a pressure of…

A:

Q: onsider (Figure 1). The cord is attached to the 36-lb block, and the coefficients of static friction…

A: The weight of the block is Mg=36 lb. The weight of the wheel is mg=24 lb Static friction is μb=0.2,…

Q: work and heat transfer when 0.75 kg of air, at a pressure of 1.5 bar and a temperature of 27 °C,…

A: Case (i): Boyle's Law (P1V1=P2V2) Boyle's law describes an isothermal (constant temperature) process…

Q: Obtain Unit-Step Response of First-Order Systems: C (t). R(S) C(s)

A: From Block diagram: G(s)=1/sH(s)=1 The unit step input is given as: R(s)=1/s

Q: Q1/ Consider the following fluids, each with a velocity of u = 9 m/s and a temperature 10°C, in…

A: u=9m/s T∞=10oc D=10mm=0.01 m TS=50oc   To find: Q˙conv

Q: The disk is subjected to a couple moment M. The end of the spring wraps around the periphery of the…

A: The spring constant is k=4 kN/m. The radius is r=0.6 m The moment applied is M=300 N-m.

Q: Problem 1: A uniform beam of mass M = 100.0 kg and length L = 20.0 m has a load of m₁ = 3000 kg at…

A: According to the given data M=100kg Mg=100x9.81=981 N mL=3000kg mLg=3000x9.81=29430N T=12000N We…

Q: The forked rod is used to move the smooth 2-lb  particle around the horizontal path in the shape  of…

A:

Q: Figure below shows the single degree of freedom control surface/actuator system. The control surface…

A:

Q: 3. If we replace the distributed loading on the right by a single resultant force, how far from…

A: According to the given data A Beam with Uniform distributed load (Udl) and Uniform varying load…

Q: Send correct answer

A: To convert world energy consumption from quadrillion Btus to the equivalent quantities in other…

Q: Q1: Find the natural frequency co for the system shown in Fig. (1). Figure (1) X 81m, J k

A: Here we apply D Alembert's principle to find out the frequency of oscillation in figure 1).

Q: For the one-dimensional indicates that the entire rod is held at a constant temperature for all t>0.…

A: The one-dimensional heat equation is a partial differential equation which used to describes the…

Q: It is desired to meet the fresh air and heating needs of the 120-person lecture hall of the Faculty…

A: Given-Infromation: 120-personTemperature, T = 50°CAir per person =20m3/hCp=0.24…

Q: QUESTION 1 Two 50 mm x 150 mm rectangular timber sections are glued together to form a T- section.…

A: According to the given data M=6 kN.m There are two rectangular timber that is glued together below…

Q: An industrial nozzle accepts steam at 1 MPa, and 300 C. From negligible velocity, the nozzle creates…

A: Given: Inlet pressure: 1 MPa Inlet temperature: 300 C Exit pressure: 800 kPa Exit velocity: 200 m/s…

Q: Consider the shaded area shown in (Eigure 1). Suppose that a-140 mm, b-150 mm, and r= 75 mm. Figure…

A: According to the given data We need to find Moment of inertia about the y-axis

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter…

A: Given:Length of the shaft, L=1103 mmOuter diameter of the hollow shaft, D=73 mmInner diameter of the…

Q: wouldn't your last equation be Q/A= H (Tair-Tsurface)

A: Required:The explanation on the equation of heat flow per unit area, QA=h×To,surface-Tair

Q: Bar AB has an angular velocity AB = 9 rad/s. (Figure 1) Figure AB 200 mm 0=45° 500 mm 30⁰ 4 < 1 of 1…

A:

Q: The rectangular plate is subjected to the deformation shown by the dashed line. The dimensions are X…

A: According to the given data ∆y=4mm X=130mm We need to find Average shear strain in the plate

Q: True/False Statement: A cable is a load bearing component that can only support tensile forces. True…

A: Answer: False. usechatgpt init success

Q: 1. The linear impulse and momentum equation is obtained by integrating the time. a. friction force…

A: Solution.jpg

Q: I can't see the right side of the answer

A:

Q: We need a steam turbine is to generate 10 MW of power. The feed steam is 200 bar at 500 C. The…

A:

Q: 9. When calculating work done by forces, the work of an internal force does not have to be…

A: In order to move a body through a certain distance, some amount of energy is required. This energy…

Q: Water, contained in a large open tank, discharges steadily into the atmosphere from a curved pipe.…

A:

Q: 1 A thin 5m long uniform rod is free to rotate in the plane of the page about a fixed axis at Point…

A:

Q: A certain factory has an average electrical load of 1800 kW and requires 4.6 MJ/s for heating…

A: Given Data: Average Electric Load = 1800 kW Required heating Load = 4.6 MJ/s=4.6 MW Initial…

Q: CALCULATE AND DRAW THE SHEAR AND MOMENT DIAGRAM.

A: Given: Find: Draw the shear and moment diagram.

Q: A dc transformer is supplied with electric power at 230 watts with an input voltage of 220 volts.…

A:

Q: Q2 A short cylindrical billet 16 mm diameter and 40 mm gauge length is elongated under tensile load…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q&amp; A…

Q: 6. a) The 30-g bullet is traveling at 400 m/s when it becomes embedded in the 2-kg stationary block.…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.