A rectangular bar of length L has a slot in the central half of its length. The bar has width b, thickness t, and elastic modulus E. The slot has width b/3. If L = 370 mm, b = 57 mm, t = 11 mm, and E = 78 GPa, determine the overall elongation of the bar for an axial force of P = 11 kN. 3 Answer: i mm 17 1/27

A rectangular bar of length L has a slot in the central half of its length. The bar has width b, thickness t, and elastic modulus E. The slot has width b/3. If L = 370 mm, b = 57 mm, t = 11 mm, and E = 78 GPa, determine the overall elongation of the bar for an axial force of P = 11 kN. 3 Answer: i mm 17 1/27

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Draw a free body diagram of rigid bar ABD, and determine the magnitude of the vertical reaction force at pin D.Answer:D = kN
In the figure, determine the value of S such that the resultant is 100 N downward and acting at 3 meter from the support.
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Determine the internal force and the change in length of section (1) of axial member CDE. Tension and elongation are positive. Compression is negative.Answer:F1 = kNδ1 = mm
Figure 1a shows a simply supported beam, AB of length L = 5.6 m, with a uniform distributed load of w = 4.5 kN/m. The shear force diagram is shown below the beam and the cross-section in Figure 1b. The cross section has a constant thickness t = 8.7 mm, the width of the flange is b = 217.5 mm and height of the web is d = 211.41 mm. 1. Determine the position of the neutral axis. 2. Determine the moment of inertia about the neutral axis
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 450 mm2. Determine the average axial stress in each bar. q = 5 t = 0
The system shown in the figure consists of two bars and is subjected to a force at B and C.[d1 = 53 mm, d2 = 32 mm, L1 = 1.2 m, L2 = 1.3 m, E= 120 GPa, PC = 35 kN, PB = 35 kN] Determine the deformation of rod (2)? Determine the displacement of point C?in mm
There is a beam subject to a uniform force w as shown in the figure below. The E of the entire section is 200 GPa and I is 60x10^6 mm^4. (a) Calculate the reaction force at point c and the vertical displacement at point B (b) If the support point C sinks downward by 0.1m for some reason, calculate the reaction force at point C and the vertical displacement of point B.
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
where, bf1= 260 bf2 = 120 tf = 25 tw = 16 d1 = 160 d2 = 110 1. Calculate the location of the neutral axis from the bottom of the beam in mm. 2. Compute for the moment of inertia in 1x10^6 mm^4. 3. What is the value of in kN/m, considering flexural stress in tension? 4. What is the value of in kN/m, considering flexural stress in compression? 5. What is the statical moment of area (Q) in 1x10^3 mm^3 ? Use three decimal places. 6. What is the value of in kN/m, considering shear stress at the welded section? 7. What is the safest value of in kN/m? Use three decimal places.
For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the deformation incurred by rod CD. Also, calculate the angle of tilt in radians for bar AC and the horizontal displacement of point F. Use E = 120 GPa
In the figure, the rigid AD bar is held vertically by two elastic rods articulated at the ends, which are horizontal at points B and C. Under the effect of a horizontal load of 120 kN of the system; a) Calculate the forces to occur in the elastic bars, b) The displacement of the top point (A) of the rigid bar. Note: (EA = 108N)