A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places

A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three resultant forces as follows: 70 kips compression in the x direction, 55 kips tension in the y direction, and 48 kips tension in the z direction. If ν = 1/3 and E = 29 x 106 psi, ( a ) determine the single resultant load in the z direction that would produce the same deformation in x direction as the original loadings, ( b ) determine the single resultant load in the y direction that would produce the same deformation in z direction as the original loadings, and ( c ) determine the single resultant load in the x direction that would produce the same deformation in y direction as the original loadings.
Find the value of uniform load (w) [ Kip/ft if the stresses in steel and aluminum are 22ksi and 15ksi respectively. w(kip/ft) ] 15ft 3in 3in 3in
The two-bar structure shown is pinned at A, B, and C. A sign weighing 20 kN is suspended from bar BC at points D and E, which are located at 0.8 m and 0.4 m, respectively, from the ends of the bar BC. If member AB is a steel pipe with inside diameter 20 mm, determine the smallest permissible outer diameter of the member if the working stress in steel is not to exceed 140 MPa.
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION,20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE XDIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF AUNIFORMLY DISTRIBUTED FORCE OF Px=3kN (COMPRESSION), Py=4kN(TENSION) AND Pz=7kN (COMPRESSION) IN THE X, Y AND Z DIRECTIONSRESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa,DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSODETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THEWOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.
The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 , and if this section is under a bending moment of 22 kN m, please calculate the normal stress at Point B: ____ MPa. Calculate your answer to 1 decimal place.
The steel framework is used to support the reinforced concrete cinder, as shown in Figure 2. (Hint: see table ). The thickness of the slab is 4 inches, and the slab carries a uniform live loading of 300 lb/ft2. Sketch loading.
The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its strength in mm at section a-a. Est = 200 GPa, vst = 0.29
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.6 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 89.31 MPa and its angle of twist is limited to 5.38˚. Use G = 80.35 GPa for steel and L = 455 mm. Round off the final answer to two decimal places.
A wooden beam is fabricated by nailing together three boards as shown. The boards have dimensions of b1 = 20 in., d1 = 1.2 in., b2 = 1.2 in., d2 = 19 in., b3 = 10 in., and d3 = 1.2 in. The vertical distance from the bottom edge of the section to the centroid is 12.761 in. The moment of inertia of the section about the z axis is 4113 in.4. Determine the maximum shear stress in the cross section if the internal shear force is V = 440 lb. Assume that the shear force V acts in the y direction. Part 1 The maximum shear stress will occur at the centroid. Cut a cross section along the centroidal z axis and calculate the first moment of area at this section.Answer:Qmax = in.3