A rectangular block of a material with a modulus of rigidity of FN ksi is bonded to two rigid horizontal plates. The lower plate is fixed, while the upper plate is subjected to a horizontal force P. Knowing that the upper plate moves through 0.04 in. under the action of the force, determine (a) the shearing strain in the material, (b) the force P exerted on the upper plate. 2.5 in. 8 in., 2 in.

A rectangular block of a material with a modulus of rigidity of FN ksi is bonded to two rigid horizontal plates. The lower plate is fixed, while the upper plate is subjected to a horizontal force P. Knowing that the upper plate moves through 0.04 in. under the action of the force, determine (a) the shearing strain in the material, (b) the force P exerted on the upper plate. 2.5 in. 8 in., 2 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A rectangular aluminum block having a dimension of (from origin) for the +250 mm along the Y-axis, -100 mm along the X-axis, and -175 mm along the Z-axis. The applied forces are (at both sides) 375 kN tension along the X-Axis, 200 kN tension along the Z-axis, and 150 kN compression along the Y-axis. If the poisson’s ratio is 0.28, and E = 76 GPa, determine the strain and deformation along X, Y, and Z – axis.
A standard tension test is used to determine the properties of an experi-mental plastic. The test specimen is a 58-in.-diameter rod and it is subjected to an 800-lb tensile force. Knowing that an elongation of 0.45 in. and a decrease in diameter of 0.025 in. are observed in a 5-in. gage length, determine the modulus of elasticity, the modulus of rigidity, and Poisson’s ratio for the material
A standard tension test is used to determine the properties of anexperimental plastic. The test specimen is a 15 mm diameter rod and it issubjected to a 3.2 kN tensile force. Knowing that an elongation of 11 mmand a decrease of diameter of 0.625 mm are observed in a 120 mm gagelength, determine the modulus of elasticity, the modulus of rigidity, andPossion’s ratio of the material.
In a standard tensile test, a steel rod of 22-mm diameter is subjected to a tension force of 75 kN. Knowing that ν=0.30 and E=200 GPa, determine (a) the elongation of the rod in a 200-mm gage length, (b) the change in diameter of the rod
When subjected to a compressive load, the length of the rod is 199,6 mm, and its diameter is 10 mm. If the original length was 200 mm, and modulus is 70 GPa, determine: 1.1 The stress and strain in the rod when loaded. 1.2 The magnitude of the load.
Question 1For the steel truss (E= 200 GPa) and loading shown in the figure, determine the deformations of members AB and AD, knowing that their cross-sectional areas are 2400 mm2 and 1800 mm2, respectively.
At a point in a material under stress there is a compressive stress of 200MN/m2 and a shear stress of 300MN/m2 acting on the same plane. Determine the principal stresses and directions of the planes on which they act
A rod 200 cm long and of diameter 3.0 cm is subjected to an axial pull of 30 kN. If the Young’s modulus of the material of the rod is 2 × 105 N/mm2, determine: (i) stress, (ii) strain and (iii) the elongation of the rod.
A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of 200 MPa. The rod is 250 mm long and one part of its length is square and the remainder is circular with a diameter of 25 mm. If the total strain energy in the rod and modulus elasticity of the material is 1.3 J and 200 GPa, determine the following:1.The applied load F2.The total extension of the bar3.The length of the square portion of the bar4.The suddenly applied load that will induce the same amount of energy 5.The load that falls from a height of 8 mm induces 1,3 J in the bar.
The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm and a thickness of 13 mm. Knowing that each pin has a diameter of 10 mm determine the value of the maximum average normal stress on rod BD considering the angle θ=90°. Calculate the deformation in the BD rod knowing that it is made of steel with an elastic modulus equal to 210GPa. Knowing that pins A, B and D are made of steel with a limit stress of 180Mpa, calculate the smallest allowable diameter so that they support the load applied to them considering an overall safety factor of 2,8.
A rectangular aluminum block is 100 mm long in the x direction, 75 mm wide in the y direction and 50 mm thick in the z direction. It is subjected to a triaxial loading consisting of a uniformly distributed tensile forces of 200 kN in the x direction and uniformly distributed compressive forces of 160 kN in the y direction and 220 kN in the z direction. If n = 1/3 and E = 70 GPa, determine the resultant deformation in the x, y and z direction. Determine also a single distributed loading in the x direction that would produce the same z deformation as the original loading.
Suppose that σx = 42 MPa . A) Determine the orientation of principal planes of stress. B) Determine the orientation of the planes of maximum in-plane shear stress.