A rectangular reinforced concrete beam carries service loads on a span of 20 ft as shown. Use fc' = 3000 psi and fy = 60,000 psi; b = 14.5 in., d = 23.5 in., and reinforcing is three No. 10 bars. Determine whether the beam is adequate with respect to moment. och DL = 1.6 kips/ft 6' 0" LL = 2.8 kips/ft

A rectangular reinforced concrete beam carries service loads on a span of 20 ft as shown. Use fc' = 3000 psi and fy = 60,000 psi; b = 14.5 in., d = 23.5 in., and reinforcing is three No. 10 bars. Determine whether the beam is adequate with respect to moment. och DL = 1.6 kips/ft 6' 0" LL = 2.8 kips/ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ASAP PLEASE
A rectangular beam has a width of 300 mm and an effective depth of 537.50 mm to the centroid of tension steel bars. Tension reinforcement consists of 6-28 mm diameter in two rows, compression reinforcement consists of 2-22 mm. £c= 27.6 MPa, fy= 414.7 MPa. Assume steel covering is 60 mm for compression bars. Calculate the Moment Capacity of the Beam
Beam section is b = 300mm, h = 450 mm. %3D Steel cover is 75 mm. Compressive strength of concrete fc' = 20.7 MPa, steel strength fy = 415 MPa. The beam is simply supported on a span of 5m and carries the following loads: dead load = 13 KN/m, live load = 10 KN/m. Find the required %3D number of 20mm Ø bars for the given cross section both in balance and ultimate condition.
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa. Answer must be in mm. Given: a = 1 m, b- 4 m. c= 2 m, P- 6 kN, and w = 3 kN/m. P kN 上 cm w kN/m (not scaled) 240 mm, a m bm Ri R,
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b=4 m, c = 2 m, P=6 kN, and w 3 kN/m.
Please answer as soon as possible.
Determine the design flexural strength in ft kips of a W10X26 of A242 (Fy = 50ksi) steel subject to a. Continuous lateral support. Blank 1 b. An unbraced length of 10 ft with Cb = 1.0. Blank 2 C. An unbraced length of 20 ft with Cb = 1.0. Blank 3 W10x26 A = ... 7.61 in.^2 d = 10.300 in. tw = 0.260 in. bf = 5.770 in. tf = 0.440 in. T= 8-1/4 in. k = 0.7400 in. k1 = 0.6875 in. gage = 2-3/4 in. rt = d/Af = Ix = Sx = 1.540 in. 4.07 144.00 in.^4 27.90 in.^3 rx = 4.350 in. ly =| 14.10 in 4 S = 4.89 in.^3 ry = 1.360 in. Zx = 31.30 in.43 Zy = 7.50 in 43 J = 0.40 in.^4 Cw = 345 in.^6 a = 47.14 lin. Wno = 14.30 in.^2 9.05 Sw = Qf = in.4 5.99 in.43 Qw = 15.50 in.^3 I||| I|||
Determine the minimum cross section controlled by shear. Ans.: b = _________ mm and d = _______ 2 mm
Find internal force using method of joint
Design the shear reinforcement for the given beam below. Use fys = 275 MPa , fy = 415 MPa , fc' = 21 MPa b = 150 mm, d = 325 mm, ds = 10 mm dbt = 16mm , dbc = 12 mm. Column = 300 mm x 300 mm Calculate s in mm (answer should be divisible by 10)
F- 3 kN 500 mm P = 2.8 kN y Figure Q1 400 mm A z Figure Q1 shows one 'L’shaped beam ACD which is built -in at one end. It is loaded with load F=2.5kN at its free end D and with load P= 3.5kN at point C. The beam has solid round cross-section with diameter of 100 mm. The beam is made of steel with E= 200 GPa and v= 0.3. Use point B as the critical point to be analysed a) Calculate the respective stresses values and draw the stress element at point B in the x-y direction. b) Calculate and draw the principal stress element & maximum shear stress element. c) If a strain gauge is fixed at point B at -20 degrees from the x-direction, calculate its value.