Using the approximate equation, determine the number of #8 bars required to support a bending moment of 130k-ft Refer to the following reinforced concrete beam information. Material properties are: fc = 5 ksi fy = 60 ksi Moment capacity equations: Analytical method: M = Ø. As-fy.d (1-0.59 Asy) Approx. method: Mu = 4A,d 6-#8 4-#8 3-#8 2-#8 24" -12" BEAM SECTION #4 STIRRUPS #8 LONG. BARS 2" COVER OVER THE STIRRUPS [k-in] [k-ft]

Using the approximate equation, determine the number of #8 bars required to support a bending moment of 130k-ft Refer to the following reinforced concrete beam information. Material properties are: fc = 5 ksi fy = 60 ksi Moment capacity equations: Analytical method: M = Ø. As-fy.d (1-0.59 Asy) Approx. method: Mu = 4A,d 6-#8 4-#8 3-#8 2-#8 24" -12" BEAM SECTION #4 STIRRUPS #8 LONG. BARS 2" COVER OVER THE STIRRUPS [k-in] [k-ft]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the required steel area for a reinforced concrete T-beam with an effective flange width of 1200 mm and a slab thickness of 100 mm. The beam is to carry an ultimate moment of 1300 kN-m. The width of the web is 300 mm and the effective depth is 550 mm. Assume f’c = 28 MPa and fy = 400 MPa * a. 7772 mm² b. 8256 mm² c. 7932 mm² d. 7232 mm²
A rectangular reinforced concrete beam 325 x 550 mm (b x d) is provided with 3H25 bar (As = 1473 mm2) as compression steel. Determine the area of tension steel needed for the beam to attain its full moment capacity. Calculate the corresponding ultimate moment of resistance. Assume fck = 30 N/mm2and fyk = 500 N/mm2and d’ = 55mm. Take until 2 decimal point for each calculation. Notes : Internal forces Fcc = 0.567fck(b x 0.8x) = 0.454 fck bx Fst = 0.87 fyk As Moment of resistance with respect to steel, M = Fcc.z Moment of resistance with respect to concrete, M = Fst.z Mbal = Kbal fck bd2 where Kbal = 0.167…
Question 45 Calculate the nominal shear strength (kN) of 4-legged stirrups 10-mm-diameter, spaced at 210 mm on centers for a beam with effective depth of 470 mm. Use yield strength of stirrups fy = 275 MPa.
calculate the nominal shear strength(kN) of 4-legged stirrups 12 mm diameter, spaced at 280 mm on centers fo a beam with effective depth of 417 mm. use yield strength of stirrup fy = 275 Mpa.
A reinforced concrete rectangular beam has a width of 315mm and an effective depth of 525mm. The beam is reinforced with six 25mm diameter tension bars. Take fy=400MPa and fc=29.50MPa. What is the nominal moment capacity of the beam, kN-m? What is the balanced steel area, mm2?
6 Calculate the nominal shear strength (kN) of 4-legged stirrups 10-mm- diameter, spaced at 210 mm on centers for a beam with effective depth of 470 mm. Use yield strength of stirrups fy = 275 MPa.
A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2
The following T-Beam has given properties: Effective Depth (d) = 485 mm, thickness of the slab = 100 mm. Web thickness of 300 mm, and the span of the beam is 5.0 m having a spacing of 2.4 m, center to center. The live load moment of 163 kN-m, and a dead load moment of 84 kN-m, these moments are unfactored. fc' =20.7 MPa, fy = 413.7 MPa, d' = 65 mm. b) Determine the value of "a" (Take the beam as Tension-Controlled)
The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit weight =23.6KN/m^3) resting on the three 8m spanned RC floor beams spaced at 1.6 meters on center. Size of RC beam is 200mm x 450mm. NSCP load factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the unfactored slab load in KN/m? express your answer in 1 decimal place.
A reinforced rectangular beam with width 437.5 and effective depth 692.5 is subjected to service liveand dead loads (self-weight included) of 56 and 70.5, respectively. If required, compressionsteel bars are to be placed at a distance d′ = 692.5 from the extreme compression fiber. Use ??′ =28 ??? and ??= 420 ???. Compute the following: 1. Solve for the area of tension steel bars using ?? = 0.004.2. Solve for the area of compression steel bars using ?? = 0.004.3. Solve for the area of tension steel bars using ?? = 0.005.4. Solve for the area of compression steel bars using ?? = 0.005
Please Answer it fast on Sheet of paper. F1=1.5KN ,F2=3.8KN, a=3.6m ,b=2.0m ,c=1.3m. You need to find Forces in member (CH,AH and CD) And whether it's +ve or -ve.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa