Determine the load that can be applied at the end of the rigid bar if the stressin either spring shown in the figure shall not exceed 200MPA.Spring 120Spring 2n30d10mm20mmD150mm120mmG83GPA35GPA2mwww

Step 1: Spring stiffness: Stiffness of first spring= 83 x 103 x 10^4/(8x150^3x20) =1.537 N/mm…

Determine the load that can be applied at the end of the rigid bar if the stress either spring shown in the figure shall not exceed 200MPA. Spring 1 20 Spring 2 30 d 10mm 20mm D 150mm 120mm G 83GPA 35GPA 2m 2M

Determine the load that can be applied at the end of the rigid bar if the stress either spring shown in the figure shall not exceed 200MPA. Spring 1 20 Spring 2 30 d 10mm 20mm D 150mm 120mm G 83GPA 35GPA 2m 2M

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.4.3P: Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the...

See similar textbooks

Related questions

Q: Determine Poisson's ratio for which young's modulus is 1.4x10^ 5 N/mm2 and the modulus of rigidity i...

A: Given Young's modulus of elasticity, E = 1.4*105N/mm2 Modulus of Rigidity, G = 4.8 * 104N/mm2 To Det...

Q: Find pressure at 10 m depth

A: Given data : Acceleration due to gravity=g g=9.81 m/s2 Depth=h h=10 m Density of water=ρ ρ=1000 kg/m...

Q: ANGLE MEASURED VALUE ANGLE MEASURED VALUE 312 o'24" 4759' 40" 137 10' 29" 57 02' 42" 100 40' 25" 65 ...

Q: What is the distance between the front and rear axle of H Truck in meters?

A: the distance between the front and rear axle of H Truck in meters is equal to the distance between c...

Q: PROBLEM 4 For the figure shown, determine the stresses of the wires and the elongation when the temp...

A: Given data in question UVL Steel and aluminum wires Length Area Modulus of Elasticity Coefficient ...

Q: A snowball rolls off a barn roof that slopes downward at an angle of 40°. The edge of the roof is 14...

Q: Consider the following simply supported beam with a concentrated dead load acting at a distance of 6...

A: Given, L=18ft X=6ft Dead load = 38k Uniform live load = 2.7k/ft n=8 fc'=3000psi Our aim is to deter...

Q: Write the shear and moment equations (simplified and not simplified) at each segment of the beam. Dr...

Q: Determine Poisson's ratio for which young's modulus is 1.4x10^ 5 N/mm2 and the modulus of rigidity i...

A: Given data : Modulus of rigidity (G)=4.8×104 N/mm2 Youngs modulus (E)=1.4×105 N/mm2 To find : Pois...

Q: 44. Which of the below is not an example of a base? A. O White lead B. O Cobalt C. O Zinc oxide D. O...

A: Base in paints are metallic oxide used in order to reduce the shrinkage at the time of drying.

Q: . What is the problem of rehabilitation?

A: To find: Problem of rehabilitation

Q: Q1/ If the beam is subjected to a shear force of V= 80 kN, determine the shear stress developed at p...

A: FIND MOI :I=2[20×200312]+[260×20312]=2.668×107mm4

Q: determine the normal stresses in the aluminum and bronze rodsa

Q: Given the following data for a closed traverse in which the length of D and the bearing of EA have n...

A: Answer To calculate the length of DE and bearing of EA we need to find the latitudes and departure o...

Q: 4 ft 5 ft 5 ft 6 ft FB=10 kips Fc=20 kips Fo 15 kips RE RA

Q: The annual rainfall at a place for a period of 22 years is given below. (Year started: 1951) ( 49.7,...

Q: AW 14 x 68 having the following properties: Prop. of W 14 x 68 Sx = 1688 x 10° mm Cb = 1.14 Lp = 2.6...

A: We have to determine the value of flexural strength of the beam if the beam has an unbraced length o...

Q: Problem 2: A home is on fire, and to prevent its spread to the next house, firefighters are spraying...

Q: 8. Rehabilitation of structures may be required due to several reasons. Choose the correct reason.

A: The term "rehabilitation" refers to the process of restoring a building or structure to a usable sta...

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown, determi...

Q: 5. From the cantilever beam below, determine the value of point load P acting at midspan that will e...

A: To find value of load P such that deflection at free end is zero

Q: Rehabilitation of structures may be required due to several reasons. Choose the correct reason.

A: To find: Why rehabilitation of structure may be required

Q: The head over a ??????????-crested weir, whose breadth is 5m, is 4m. Given that discharge coefficien...

Q: The total headloss from A to D is 9m. Using f= 0.02. L=450m D=300mmg A D L-450m D=450mmø L=200m D=20...

Q: The time to reach 50% consolidation is 800 seconds for a soil sample of 10 cm thickness, tested in a...

Q: sing cantilever method, determine the maximum absolute axial force in the column in kN due to latera...

Q: Q3. Analyse the gable frame shown in FIG.3 by the slope deflection method. Draw the bending moment a...

Q: Situation no. 1: Calculate the bending stresses in the concrete and the reinforcing steel, using the...

Q: 1. The rigid beam AB is pin supported at A and supported by a cable BC as shown in the figure. Deter...

A: Given: The stress in the cable is 15 ksi. Consider the figure,

Q: Example 6.5. The lowest level of an impounding reservoir, situated in hills and being used as a sour...

Q: G, = 2.69; e = 0.47 G, = 2.73; e = (0.68 G. = 2.7; e = 0.89

Q: PROBLEM 1 Determine the load that can be applied at the end of the rigid bar if the stress in either...

A: K1 = 83 x 103 x 10^4/(8x150^3x20) =1.537 N/mm K2 = 13.5 N/mm 8Wx150/ πx10x10x10 + 8Wx120/ πx20x20x20...

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple sy...

Q: Explain E-waste and tell its mix proprtion of cement aggregate and e waste as percentage and also wr...

A: Definition of E-waste: E-waste is any electrical or electronics equipment that's been discarded. Thi...

Q: Explain why we need standards and codes.

A: The standards and codes are laid by every country while designing any product or structure to mainta...

Q: FROM THE GIVEN DATA OF A CLOSED TRAVERSE, FIND THE ADJUSTED BEARING OF BC AND DA USING COMPASS RULE.

A: From the above table we are determining the adjusted Bearing,The adjusted bearing of BCTha adjusted ...

Q: In your engineering survey course, your instructor put you in a group to help a transportation engin...

Q: Discuss the uses for topographic surveys.

A: A topographic ground assessment might well be required to identify distinctive aspects and altitudes...

Q: What is the energy loss through a length of pipe from which all the discharge is taken out uniformly...

Q: In prestressed concrete structures the primary problem is damaged caused to

A: To find: Why primary damaged is caused.

Q: The mechanical efficiency of the pump is 0.85 and pumping with a rate of 650 gal/min of engine oil a...

Q: contrast Portal Method and Cantilever Method.

Q: A tracer takes 100 days to travel from Well-I to Well-2 which are I00 m apart. The elevation of wate...

Q: 1. Determine the force in each member of the loaded truss shown below by Method of Joints. C D 4 m E...

A: The given truss is shown below:

Q: Use the substitute member to make a complete analysis of the complex truss shown. d 3m 25kN - 4 m e1...

Q: Problem: (General Coplanar Force System) The force system shown consists of the couple C and four fo...

Q: Situation 2] A surveyor was tasked to cut off a required area by a line through a given point. In th...

Q: what is the meaning of error propagation?

A: The act which is not proper is known as error.

Q: 2. From the closed compass traverse shown, if the forward bearing of line AB is N 78°9' E, compute t...

A: Lattitude and Departure signs N-E : Both positive S-E : Lattitude negative Departure positive S...

Q: The upper and lower stadia hair readings on a stadia rod held at station B were observed as 4 and 2....

Concept explainers

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.

Question

100%

Determine the load that can be applied at the end of the rigid bar if the stress
in either spring shown in the figure shall not exceed 200MPA.
Spring 1
20
Spring 2
n
30
d
10mm
20mm
D
150mm
120mm
G
83GPA
35GPA
2m
www

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN at D (see figure). Let the dimension variablebe b = 240 mm.(a) Find the minimum permissible diameter dminof the bracket if the allowable normal stress is110 MPa.(b) Repeat part (a), including the weight ofthe bracket. The weight density of steel is77.0 kN/m3.
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.201 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=19 kips, Q=13 kips, L1=7 ft, L2=9 ft, and L3=9 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
Tow square bars are welded together and loaded axially as shown: Determine The normal stress between A&B The normal stress between B&C The normal stress between C&D The total change in length of the bar Assume : w1 =40 mm, w2 = 50 mm, P1 = 130 kN, P2= 65 kN, and P3 =260 kN. E = 200,000 Mpa original lengths LAB = 100 mm, LBC = 120 mm, and LCD = 130 mm,
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
The control arm is subjected to the loading shown. The allowable shear stress for the steel pin is τ = 10 ksi. Determine the required diameters of the steel pins at A and C. Write your final answer to the nearest three decimal places.
The lap joint shown is fastened by five ¾ inch-diameter rivets. The bearing stress in the plates is limited to 15 ksi and the shearing stress in the rivets is 10 ksi. Assume the applied load is equally distributed among the five rivets. The thickness of each plate is ½ inch. Calculate the load P based on each stress given. Determine the maximum safe load P that can be applied. Express the loads in kips.
The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg block is attached. Each steel bar has an area of 566mm^2 and E=200Gpa. For the bronze barn the area is 866mm^2 and E=83Gpa. Find the stresses developed in each bar.
A cantilever beam AB of length L = 6.5 ft supportsa trapezoidal distributed load of peak intensity q,and minimum intensity q/2, that includes the weight ofthe beam (see figure). The beam is a steel W12 X14wide-flange shape (see Table F-1(a), Appendix F).Calculate the maximum permissible load q basedupon (a) an allowable bending stress σallow =18 ksiand (b) an allowable shear stress τallow = 7.5 ksi.Note: Obtain the moment of inertia and section modulusof the beam from Table F-1(a).
The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips whenbolted between double brackets at A and B. the bar will be fabricated from 0.5* ? inches thick plate. Forthe grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearingstress = σb = 55 ksi and Shearing stress = τ = 4.5* ? ksi. Solve for the values of (a) the diameter d of thebolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.