A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three resultant forces as follows: 70 kips compression in the x direction, 55 kips tension in the y direction, and 48 kips tension in the z direction. If v = 1/3 and E = 29 x 106 psi, ( a ) determine the single resultant load in the z direction that would produce the same deformation in x direction as the original loadings, (b) determine the single resultant load in the y direction that would produce the same deformation in z direction as the original loadings, and (c) determine the single resultant load in the x direction that would produce the same deformation in y direction as the original loadings. 55 kips 48 kips 70 kips 4 in. 3 in. 2 in.

A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three resultant forces as follows: 70 kips compression in the x direction, 55 kips tension in the y direction, and 48 kips tension in the z direction. If v = 1/3 and E = 29 x 106 psi, ( a ) determine the single resultant load in the z direction that would produce the same deformation in x direction as the original loadings, (b) determine the single resultant load in the y direction that would produce the same deformation in z direction as the original loadings, and (c) determine the single resultant load in the x direction that would produce the same deformation in y direction as the original loadings. 55 kips 48 kips 70 kips 4 in. 3 in. 2 in.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three resultant forces as follows: 70 kips compression in the x direction, 55 kips tension in the y direction, and 48 kips tension in the z direction. If ν = 1/3 and E = 29 x 106 psi, ( a ) determine the single resultant load in the z direction that would produce the same deformation in x direction as the original loadings, ( b ) determine the single resultant load in the y direction that would produce the same deformation in z direction as the original loadings, and ( c ) determine the single resultant load in the x direction that would produce the same deformation in y direction as the original loadings.
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its strength in mm at section a-a. Est = 200 GPa, vst = 0.29
A hollow circular column of steel (E = 30,000 ksi) is subjected to a compressive load P. The column has length L = 8.0 ft and outside diameter d = 8 in. The load P = 110 kips. (a) If the allowable compressive stress is 8.1 ksi, what is the required inside diameter (inches)? (b) If the allowable shortening of the column is 0.025 in., what is the required inside diameter (inches)?
Determine the slenderness ratio and the Euler buckling load for round wooden dowels that are 3.00 m long and have a diameter of (a) 19 mm and (b) 29 mm. Assume E = 14 GPa. Answer:(a) Slenderness ratio = Pcr = N (b) Slenderness ratio = Pcr = N
Find the value of uniform load (w) [ Kip/ft if the stresses in steel and aluminum are 22ksi and 15ksi respectively. w(kip/ft) ] 15ft 3in 3in 3in
A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and crosssectional area equal to 1000 ??2 fits snugly between two rigid walls. Determine the change in length due to the applied load. Use ? = 0.30. (Answer in three decimal places and in mm)
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
A square timber column, 10 in. by 10 in. in cross section, is reinforced on all four sides by copper plates, each plate being 10 in wide and “t” in thick. Determine the smallest value of “t” for which the column can support an axial load of 560 kips if the working stresses are 1250 psi for timber and 17 ksi for copper. The moduli of elasticity are 1.5 × 10^6 psi for timber and 17 × 10^6 psi for copper.
A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are symmetrically spaced and 20 feet long. The two outer wires are steel and the middle wire is brass. Calculate: a) Stresses in the wires
A tapered rod with length c = 7m and cross - sectional dimensions a = 270n mm and b = 119 mm is carrying an axial load P = 75kN . If the modulus of elasticity of the rod is E = 164GPa , determine the elongation of the rod in mm . Final ans. in 3 dec place
From the figure shown, fc’ = 20 MPa, fs = 140 MPa, and n = 12. Determine the moment capacity of concrete and steel (Cracked Analysis Only)