A Reg.No-m length of smooth horizontal pipe is attached to a large reservoir as shown in Fig. 2. A pump is attached to the pipe to pump water into the reservoir at a volume flow rate of 0.01 m/s. What pressure must the pump produce at the pipe to generate this flow rate? The inside diameter of the smooth pipe is 75 mm. Pb # 4:

A Reg.No-m length of smooth horizontal pipe is attached to a large reservoir as shown in Fig. 2. A pump is attached to the pipe to pump water into the reservoir at a volume flow rate of 0.01 m/s. What pressure must the pump produce at the pipe to generate this flow rate? The inside diameter of the smooth pipe is 75 mm. Pb # 4:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at 20°C ( ρ= 999.7 kg/m3 and μ=9.7720 x10-4 kg/m · s) is flowing steadily in a hexagonal cross sectional pipe b=1.5cm, 20-m-long at an average velocity of 1.2 m/s. Determine: (a) Hydraulic diameter. (b) The pressure drop. (c) The head loss. (d) The pumping power requirement to overcome this pressure drop.
4. A reservoir supplies water to a horizontal 6′′ pipe 800 ft long. The pipe flows full and discharges into the atmosphere at the rate of 2.23 cfs. What is the pressure in psi midway in the pipe, assuming the only lost head is 6.20 ft in each 100 ft of length? indicaye free body diagram
A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The center of the door is 4.5m below the dam’s water level. Assuming the unit weight of water is 9.79 kN/m3. Compute the hydrostatic force acting on the door.
Hydraulics ProblemAn open horizontal tank 1.5m high 2m wide and 5m long is full of oil with a specific gravity of 0.9. It is accelerated in the direction parallel to the longer length at 2.3 m/s2 a. What is the force acting on the wall of the tank with the shortest depth in KN? b. If the acceleration is increased by 0.88 m/s2. Determine the volume of oil that spilled out the tank?Note: Draw free-body diagram and used 4 decimal places
A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The center of the door is 4.5m below the dam’s water level. Assuming the unit of water is 9.79 kN/. Compute the location of the center of pressure from the centroid of the door.
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
A 3-m wide, 8-m high, rectangular gate is located at the end of a rectangular passage that is connected to a large open tank filled with water as shown below. The gate is hinged at its bottom and held closed by a horizontal force, FH, located at the center of the gate. The maximum value for FH is 3500 kN. (a) Determine the maximum water depth, h, above the center of the gate that can exist without the gate opening, (b) Is the answer the same if the gate is hinged at the top? Explain your answer. [Answer in units of ft. for part (a)]
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
1. A long siphon connected at the side near the bottom of the reservoir discharges water through a nozzle 200mm by 50 mm creating a jet. Various points were identified located along the siphon: Point A is located after the reservoir connection, Point B is 4 m above Point A, Point C is 3 m above Point A, and Point D is 1 m below Point A and located before the nozzle. Determine the flow in m3/s along the siphon and the pressure in kPa at Point A, Point B, Point C, and Point D. Consider that the level of the reservoir is same with Point C. Assume no head loss along the siphon. 2. Two interconnected pipes A and B with 300 mm and 200 mm diameter, respectively, carries a flow of 0.116 m3/s. Determine the velocity in m/s of pipe A and pipe B. If pipe B was replaced with 400 mm diameter, determine the velocity in m/s of pipe B. 3. The 500 mm diameter pipe conveys treated water to supply a municipality with a demand of 40 MLD. Determine the head loss in meter if the length of the pipe is 10 km…
An inclined rectangular sluice gate AB 1.2 m by 5 m size as shown in Fig. 2 is installed to control the discharge of water. The end A is hinged. Compute the total pressure, center of pressure and the force normal to the gate applied at B to open it.
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
A water main line is composed of two pipes connected in series, pipes AB and BC. Pipe AB is 500 m long and 30 cm in diameter while pipe BC is 800 m long and 20 cm in diameter. Point C is 10 m higher than point A. The pressure at point C is 3 kg per square cm higher than the pressure at point A and the coefficient for minor head losses due to contraction and enlargement are 0.40 and 0.25 respectively. Determine the discharge and flow direction on the water main line using Darcy-Weisbach formula with f = 0.02 for all pipes. Draw approximately the EGL and HGL.