Q1: Figure shows the water pipe network shown: a) Analyze the water pipe network shown take Hazen-Williams coefficient, C= 120? b) Find the velocity in each pipe? c) Select the critical path and calculate the residual pressure at point (pressure 2 m/min), if static pressure head at A 250 kPa? 6 m/min 300 mm 1000m 2.25 m/min 150 mm 1000m 1.75 m/min 2 m/min 250 mm 500m 500m ww 007

Q1: Figure shows the water pipe network shown: a) Analyze the water pipe network shown take Hazen-Williams coefficient, C= 120? b) Find the velocity in each pipe? c) Select the critical path and calculate the residual pressure at point (pressure 2 m/min), if static pressure head at A 250 kPa? 6 m/min 300 mm 1000m 2.25 m/min 150 mm 1000m 1.75 m/min 2 m/min 250 mm 500m 500m ww 007

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Similar questions

Show complete solution(need ASAP): A flow net has been drawn as shown in the figure. Points A and C are at elevation ℎ1 and ℎ2 respectively above the datum. ? = 4 m ℎ1 = 4.7 m ℎ2 = 1.4 m Determine : a. Compute the piezometric pressure at point A in kPa. b. Compute the piezometric pressure at point C in kPa. c. Compute the piezometric head at point B in meters.
Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 = 0.8335 m/s z2 = 0 m Head loss from point 1 to 2 = 0.262 m Find the pressure at point 2
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
Figure 2 represents an oil storage drum that is open to the atmosphere at the top. Some water was accidentally pumped into the tank and settled to the bottom as shown in the Figure 2. Calculate the depth of the water h2 if the pressure gage at the bottom reads 158 kPa (gage). The total depth hT = 18.0 m
Q1(b) Water flows through a pipe with a diameter of 2 m. Stagnation and static pressures measured by pitot tube are 0.3 m and 0.25 m of water, respectively. Calculate the velocity of flow
1. A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower end while 1.2 meters at the higher end. The rate of flow through pipe is 5400 liters/min. Find the pressure at the lower end if the pressure at higher end is 68.07 kPa. Neglect losses.
6. Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s. indicate free body diagram
For the data given in Problem 13.5, calculate the lateral pressure σ'a at z = 2 m, 4 m, 6 m and 8 m.
The system in Fig. P2.48 is open to 1 atm on the right side. (a) If L = 120 cm, what is the air pressure in con tainer A? (b) Conversely, if Pa = 135 kPa, what is the length L?
A conical tank is inclined with an angle of 60°. A hole with radius 2-in was opened at the bottom. If initially the tank is full to a height of 9 ft, how long will the tank drain? Consider a coefficient of contraction, 0.6.
Water at 20°C is flowing through through a narrow section as is seen in the figure. There is a 20 kPa pressure difference between the upstream and throat section as seen. The velocity in the throat section is 10 m/s. What is the velocity (m/s) in the upstream pipe?
PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at C was 38.38 fps. Diameter of the pipe is 1 inch. (b) Determine the pressure at point B in psi.