A reinforced concrete beam, size 200 mm wide and 300 mm deep overall is simply supported over a span of 3 m. It is subjected to two point loads P of equal magnitudes placed at middle third points. The two loads are gradually increased simultaneously. Beam is reinforced with 2 HYSD bars of 16 mm diameter placed at an effective cover of 40 mm on bottom face and nominal shear reinforcement. The characteristic compressive strength and the bending tensile strength of the concrete are 20.0 N/mm2 and 2.2 N/mm2 respectively. The theoretical failure load of the beam for attainment of limit state of collapse in flexure is

A reinforced concrete beam, size 200 mm wide and 300 mm deep overall is simply supported over a span of 3 m. It is subjected to two point loads P of equal magnitudes placed at middle third points. The two loads are gradually increased simultaneously. Beam is reinforced with 2 HYSD bars of 16 mm diameter placed at an effective cover of 40 mm on bottom face and nominal shear reinforcement. The characteristic compressive strength and the bending tensile strength of the concrete are 20.0 N/mm2 and 2.2 N/mm2 respectively. The theoretical failure load of the beam for attainment of limit state of collapse in flexure is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A prismatic beam having 275 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ20 mm with an effective depth of 420 mm. It is simply supported over a clear span of 6 m and designed to support a total factored uniformly distributed load of 35 kN/m over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. Determine the required nominal shear force the stirrups must sustain based on the critical shear force at a section located distance "d" from face of support. A. 15.3 B. 28.4 C. 24.2 D. 32.2
A simply-supported rectangular beam with an 8 m span has a self-weight of 5.5 kN/m and an imposed load of 12 kN/m. In addition to this, the beam supports a brickwall with a thickness of 115 mm and a height of 3.2 m. Given: density of brick wall, ρbrickwall = 19 kN/m3 ; ? = 0.8; breadth of beam, b = 175 mm; concrete strength = 25 MPa; and fsy = 500 MPa. Assume the concrete cover is 30 mm and R10 shear links are used. a. Recommend a suitable depth for the beam and determine the area of reinforcement, Ast, according to minimum ductility requirements from AS3600 (ku = 0.36) by using N32 rebar. Detail the cross-section of the beam. b. Using the same beam dimensions from (a), design the steel requirement if N25 rebar is to be used instead. c. Based on your designs using N25 and N32 rebar, which rebar size would you recommend to the client? Justify your answer.
An eight meter simply supported beam carries a superimposed dead load of 6kN/m and aservice live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively.It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPaand fy=421.60MPa. 1 Using the detailed calculation of Vc, determine the nominal shear strength of concrete at 0.60m from the support. a 133.3220 kN b 153.6610 kN c 180.3630 kN d 110.5770 kN 2 Using the detailed calculation of Vc, determine the shear carried by stirrups at 0.90m from the support. * a 53.7734 kN b 65.4637kN c 58.3913 kN d 67.2129 kN
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. b) What is the value of fs' (actual stress of the compression bars)
A reinforced concrete beam has a width of 380 mm, effective depth of 570 mm and carries a uniform live load of 90 kN/m and a uniform dead load of 60 kN/m. The reinforcing steel strength Fy = 276 MPa and specified concrete strength fc'= 21 MPa. The beam has a span of 4.0 meters Which of the following gives the factored uniform load in kN/m? What is the shear at the critical section in kN?
A reinforced concrete beam has a simple span of 8m. It carries a concentrated service load, P=200kN(40%DL and 60%LL), at midspan. The 300mmx400mm beam is reinforced with 3D25mm and 12mm stirrups. Take fc’ to be 24.50MPa fy=420MPa and fyt=280MPa. Use simplified calculation of Vc. What is the ultimate shear capacity of concrete at a section 2m from the support, kN? What should be the shear capacity of web reinforcement at the section 2m from the support, kN? What is the maximum spacing of web reinforcement allowed by the code at the section 2m from the support, mm? What is the required spacing of web reinforcement at the section 2m from the support, mm?
A 7m cantilever beam with a width of 300mm and effective depth of 500 mm isprovided with a 12mm U stirrups with fy = 345 MPa. The beam is to carry a uniformlive load of 15kN/m and uniform dead load of 14 kN/m including itsown weight throughout its entire span. Use compressive strength of concrete = 25MPa.a. Determine the distance from the support where shear reinforcement is notrequired b. Determine the spacing of stirrups at the critical section (c. Determine the spacing of stirrups at the midspan
An eight meter simply supported beam carries a superimposed dead load of 6kN/m and a service live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively. It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPa and fy=421.60MPa. a. Using the detailed calculation of Vc, determine the nominal shear strength of concrete at 0.60m from the support.
Design the middle span of a three-span, continuous, one-way slab with a short span S = 5.5 m supported a live load of 15 kN/m2 and a dead load of 5 kN/m2. Concrete unit weight is 24 kN/m3, f”c = 32 MPa, fy = 440 MPa and rebar diameter of 12 mm. Slab thickness shall be increment of 10 mm. Considering that the governing moment is the negative moment from Table 406.5.2 of NSCP 2015. a) Determine the steel-ratio provided (Use 6 decimal places) b) Unity ratio of the designed section. Show complete solution. Need ASAP. thank you.
A T‐beam has the following properties:Flange width, bf = 820 mmFlange thickness, t = 100 mm Width of web, bw= 250 mmEffective depth, d = 470 mm concrete strength f’c = 20.7 MPa steel strength, fy = 414 MPaDetermine the required tension steel area for the following conditions:A) MDL = 150 kN.m, MLL = 120 kN.mB) MDL = 175 kN.m, MLL = 190 kN.m
The figure shows a beam column joint. In a continuous building frame analysis, the maximum negative moment at the face of thesupport is 268.04 kN-m, requiring a steel reinforcement area of 1871 sq.mm. 2D36mm bars are provided. Normal density concrete is to be usedwith fc’=27.6 MPa and fy=414.7MPa
A T-Beam has the following properties: bf = 750 mm, bw 275 mm, d = 560 mm, t = 115 mm. Concrete compressive strength fc 21 MPa and steel yield strength fy 415 MPa. T-Beam is under factored moment load of 7220 kN-m. Determine the required height "z" of compression block at the web of the T-Beam.