Two shafts are connected end to end by means of a flanged bolt coupling as shown. The maximum shear stress is limited to 50 MPa in the shafts and 20 MPa in the bolts. If one shaft is solid of 100 mm diameter and the other is hollow of 120 mm external diameter, calculate the bolt diameter so that both shafts and the coupling are all equally strong in torsion. 120 mm 100 mm 200 250 mm mm Solid Hollow Flanged Bolt Coupling 24.17 mm B 27.14 mm C 21.74 mm D 24.71 mm

Two shafts are connected end to end by means of a flanged bolt coupling as shown. The maximum shear stress is limited to 50 MPa in the shafts and 20 MPa in the bolts. If one shaft is solid of 100 mm diameter and the other is hollow of 120 mm external diameter, calculate the bolt diameter so that both shafts and the coupling are all equally strong in torsion. 120 mm 100 mm 200 250 mm mm Solid Hollow Flanged Bolt Coupling 24.17 mm B 27.14 mm C 21.74 mm D 24.71 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G = 11,500 ksi] shaft (2). Tube (1) has a length of L1 = 50 in., an outside diameter of D1 = 2.55 in., and a wall thickness of t1 = 0.160 in. Shaft (2) has a length of L2 = 52 in. and a diameter of d2 = 1.35 in. If an external torque of TB = 520 lb·ft acts at pulley B in the direction shown, calculate the torque TC required at pulley C so that the rotation angle of pulley C relative to A is zero.
A solid shaft made of steel [G = 80 GPa] is subjected to the torques shown. Determine theangle of twist along the shaft measured at gears B, C, D, and E relative to the flange A. Diameter of the shaft is d= 20mm. [TB = 25 N.m; TC = 35 N.m; TD = 24 N.m; TE = 14 N.m][dABCDE = 20 mm (diameter); LAB = 300 mm; LBC = 400 mm; LCD = 400 mm; LDE = 250 mm]
From the bracket connection shown. 1. Which of the following gives the stress due to axial load. a. 62.07 MPa b. 75.56 MPa c. 52.89 MPa d. 19.34 MPa 2. What is the value of ‘b’ that will make the maximum stress due to moment equal to that due to axial load? a. 150 mm b. 200 mm c. 250 mm d. 300 mm 3. What is the eccentricity? a. 300 mm b. 250 mm c. 150 mm d. 196.78 MPa
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G = 6,500 ksi] tubes, which have an outside diameter of 2.20 in. and a wall thickness of 0.1675 in. Segments (3) and (4) are solid 1.20-in.-diameter steel [G = 11,500 ksi] shafts. The shaft lengths are L1 = 46 in., L2 = 16 in., L3 = 17 in., and L4 = 35 in. The torques applied to the shafts have magnitudes of TB = 950 lb·ft, TD = 480 lb·ft, and TE = 90 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate:(a) the magnitude of the maximum shear stress in the compound shaft.(b) the rotation angle of flange C with respect to flange A.(c) the rotation angle of gear E with respect to flange A.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 19 mm and an elastic modulus of E = 69 GPa. The steel rod has a diameter of 22 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.7 m, and c = 1.3 m. What is the magnitude of load P that is necessary to displace point A 9 mm to the left?
A compound shaft drives three gears, as shown. Segments (1) and (2) of the compound shaft are hollow bronze [G = 6,500 ksi] tubes, which have an outside diameter of 2.20 in. and a wall thickness of 0.1850 in. Segments (3) and (4) are solid 0.80-in.-diameter steel [G = 11,500 ksi] shafts. The shaft lengths are L1 = 60 in., L2 = 14 in., L3 = 17 in., and L4 = 33 in. The torques applied to the shafts have magnitudes of TB = 1000 lb·ft, TD = 480 lb·ft, and TE = 140 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. Using the sign convention presented in Section 6.6., calculate: (a) the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C with respect to flange A. (c) the rotation angle of gear E with respect to flange A.
Two solid steel shafts (shafts) in the figureconnected with gears. Permission for steel shaftsthe permissible shear stress is 7000 psi. BC spindle1.6 in diameter and 1.25 in diameter of EF shaftit is known that the width applied to the shaft at the C pointCalculate the large TC torque.
A rod 3.5 feet long rotates in a horizontal plane about a vertical axis through its center. At each end of the rod is fastened a cord 6 ft. long. Each cord is inclined at Ø = 450 with the vertical and supports a weight of 45 lbsA. Which of the following gives the speed of rotation “n” in rpm?a) n = 25.12 rpm b) n = 25.12 rpm c) n = 30.20 rpmd) n = 22.13 rpm B. What is the tension in the 5 feet long cord? a) T = 58.47 lbb) T = 63.63 lbc) T = 51.78 lb d) T = 48.25 lb
Calculate the plastic moment strength about the strong axis of a built-up I-beam with flange plates 190 mm wide, 11 mm thick and web plate 270 mm wide, 6 mm thick. Use A992 steel. Write your final answer in two decimal places in the unit of kN-m. Answer: 240.34
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
A wide flange A60 steel column has a length of 6.4meters and pinned ends. If Sx=888x103 mm3, Sy=128x103 mm3, d=358mm, bf=184mm, A=7,289mm2, Fy=414MPa, calculate the critical buckling stress, Fcr in MPa of the column. Express your answer in one decimal place.
4. A torque of 9.5 kN is to be carried by a flanged bolt coupling that consists of eight 12 mm diameter steel bolts on a circle of diameter 300 mm and six 12 mm diameter steel bolts on a circle of 250 mm. Determine the shearing stress in the bolts.