A reinforced concrete T-beam has an effective depth of 20 inches and has a reinforcement area of 7.5 square inch at the bottom. The web has a width of 14 inches and the slab thickness is 4 inches. The beam has a span of 25 feet and a spacing of 2 meters center to center of the beam. f'c= 3000 pound per square inch, Fy = 40 ksi. ww a. Determine the effective width of the flange. b. Determine the depth of compression block. c. Determine the ultimate moment capacity of the beam.

A reinforced concrete T-beam has an effective depth of 20 inches and has a reinforcement area of 7.5 square inch at the bottom. The web has a width of 14 inches and the slab thickness is 4 inches. The beam has a span of 25 feet and a spacing of 2 meters center to center of the beam. f'c= 3000 pound per square inch, Fy = 40 ksi. ww a. Determine the effective width of the flange. b. Determine the depth of compression block. c. Determine the ultimate moment capacity of the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

35 Determine the tensile steel strain (in 5 decimal places) compatible with concrete strain of 0.003 for a singly reinforced beam 300 mm wide, 600 mm deep reinforced at the bottom with 6-ϕ20 mm bars with effective depth 518 mm. Use f’c = 21 MPa and fy = 420 MPa.
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. b) What is the value of fs' (actual stress of the compression bars)
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement area of 4072 sq. mm at the bottom. fc' = 25 MPa, fy = 414 MPa. b) Determine the value of "fs"
Find shear force value under point load 10 Kn
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. determine 1.) a 2.) the value of fs' (actual stress of the compression bars) 3.) value of ρbalance 4.) Mu
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement area of 4072 sq. mm at the bottom. fc' = 25 MPa, fy = 414 MPa. a) Determine the depth of compression block, "a".
Design a reinforced concrete beam with balanced stress reinforced that will resist a bending moment of 140 kN- m assuming d= 1.5 b, fc = 12 Mpa, fs = 160 Mpa and n = 8.What will be the width of the beam?What is the value of the moment arm?What will be the steel area required?
A uniformly distributed load of 321 lb/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 10.2 inches, height, h = 15.5 inches and constant wall thickness of 1.9 inches. Determine the first moment of area, Q of the beam in mm^3 at the point of maximum shearing stress. answers should be strictly rounded-off up to two (2) decimal places
Calculate Tension BD if P = 100 kN.
4.17. A rectangular beam made using concrete with f c ′ = 6000 psi and steel with f y = 60,000 psi has a width b = 20 in., an effective depth of d = 17.5 in., and a total depth of h = 20 in. The concrete modulus of rupture f r = 530 psi. The elastic moduli of the concrete and steel are, respectively, E c = 4,030,000 psi and E s = 29,000,000 psi. The tensile steel consists of four No. 11 (No. 36) bars. ( a ) Find the maximum service load moment that can be resisted without stressing the concrete above 0 .45 f c′ or the steel above 0.40 f y . ( b ) Determine whether the beam will crack before reaching the service load. ( c ) Compute the nominal flexural strength of the beam. ( d ) Compute the ratio of the nominal flexural strength of the beam to the maximum service load moment, and compare your findings to the ACI load factors and strength reduction factor.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
A beam 200x450mm is reinforced by 2-32 mm diameter rebar. Assume cc=50mm, stirrups=10mm, fc'=21MPa and fy=415MPa. Calculate the strain of the steel reinforcement. a) 0.00182 b) 0.00201 c) 0.00224 d) 0.00391 e) 0.00577