A results of sieve analysis test for sample of Aggregate are shown in below Table: Wt Retained (gm) Sieve Size in mm 3/4" 1/2" 3/8" 19 12.5 64 9.5 111 No.4 4.75 156 No.8 2.36 201 330 266 No.16 1.18 No.30 0.600 No.50 0.300 212 No.100 0.150 200 No.200 0.075 98 Pan 75 1. Calculate percent passing through each sieve. 2. What is the maximum size. 3. What is the nominal maximum size. 4. Calculate the Fuller gradation using (n of FHWA

A results of sieve analysis test for sample of Aggregate are shown in below Table: Wt Retained (gm) Sieve Size in mm 3/4" 1/2" 3/8" 19 12.5 64 9.5 111 No.4 4.75 156 No.8 2.36 201 330 266 No.16 1.18 No.30 0.600 No.50 0.300 212 No.100 0.150 200 No.200 0.075 98 Pan 75 1. Calculate percent passing through each sieve. 2. What is the maximum size. 3. What is the nominal maximum size. 4. Calculate the Fuller gradation using (n of FHWA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following sample concrete strength data (in ksi) were collected using an ultrasonic3.5 3.2 3.1 3.5 3.6 3.2 3.4 2.9 4.1 2.6 3.3 3.5 3.9 3.8 3.7 3.4 3.6 3.5 3.5 3.73.6 3.8 3.2 3.4 4.2 3.6 3.1 2.9 2.5 3.5 3.4 3.2 3.7 3.8 3.4 3.6 3.5 3.2 3.6 3.8b) Plot a histogram for concrete strength and discuss the characteristics. The number of bins can becalculated as √number of observationc) Plot a histogram for concrete strength and discuss the characteristics with 0.1 interval width
TIME OF SETTING OF HYDRAULIC CEMENT BY VICAT NEEDLE make up solution / give example with solution ( i need example of this) Specimen No. Time (second) Penetration (mm) 1. 30 40 180 38 800 34 1200 30 2000 22 30000 2 35000 none Initial Set: __________ secondsFinal Set: ___________ seconds
How does the Duration of agitation affect the analysis of particle size in the sieving method/technique?
Sepage analysis.
Sample 2: Mass with empty mold M1 Mass of soil and mold M2 Hydraulic Head h Time interval t Volume V 145 g 250 g 950 mm 0.34 min 0.0046 L 145 g 260 g 900 mm 0.33 min 0.0049 L 145 g 228 g 922 mm 0.30 min 0.0051 L 145 g 281 g 915 mm 0.29 min 0.0044 L 145 g 219 g 908 mm 0.39 min 0.0042 L The diameter of the mold = 2.5 cm, Length of the sample = 0.3 m can u pls Find the permeability coefficient Mass of the soil Bulk Density Dry Density thank you Void Ratio
A sample of dry coarse-grained material was taken through a layer of sieves and the following results were obtained. Make the necessary calculations and draw the particle distribution curve. a.) Effective Size b. Compute the Uniformity Coefficient c.) Find the Coefficient of Curvature. d.) Sorting Coefficient e.) Percentages of Gravel, Sand, Clay and Silts using: e.1.) USDA e.2.) USCS Please answer this asap. For upvote. Thank you very much
Pls answer wt complete solution
Q3. A 1200 g sample of Gravel in the SSD condition in air and weighed 770 g when immersed in water. Also, a 500 g sample of Sand in the SSD condition in air and weighed 300 g when immersed in water Calculate the BSG(SSD) of the sand and gravel 1) the BSG (SSD) of the Gravel * 1.2.791 2.4.71 3.3.703 4.2.50 2) the BSG (SSD) of the Sand * 1.2.221 2.3.590 3.2.500 4.3.232 Choose one answer and write the answer number for me
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:Volume of bucket = 14 LWeight of empty bucket = 9.21 kgWeight of bucket filled with dry rodded coarse aggregate:Trial 1 = 34.75 kgTrial 2 = 34.06 kgMeasureSampleA B CWet Mass (g) 521.0 522.4 523.4Dry Mass (g) 491.6 491.7 492.1Absorption (%) 2.5 2.4 2.3Table P 5 . 9 determine the amount of water required to increase the moisture content of aggregate to reach absorption?5.9 Three samples of fine aggregate have the properties shown in Table Trial 3 = 35.74 kga. Calculate the average dry-rodded unit weightb. If the bulk dry specific gravity of the aggregate is 2.620, calculate thepercent voids between aggregate particles for each trial.
P.s. show complete solution pls
If Slump=120 Maximum size of aggregate=25 How is the amount of water interpolated ?
For a given sieve analysis: No. 4 - % finer 100%, for No 200 -%finer 77. LL=63, PL= 25. Classify the soil using USCS. Justify your answer. a. MH b. CL c. CH d. CL-ML