How does the Duration of agitation affect the analysis of particle size in the sieving method/technique?

Q: Which of the following terms describe shear rupture failure in block shear

A: shear rupture is type of failure occurring in the member that have both tension  on one plane and…

Q: A concrete beam sample has a width of 5 inches, a depth of 6 inches, and a length of 20 inches. The…

A:

Q: Define Tschebotarioff method.

A: The Tschebotarioff method is based on the first approximate estimation by the Tschebotarioff and…

Q: In the dry sieve analysis of soil the sieves are placed as sequential order one below the other as:…

A: answer is true   explanation is given in below step

Q: What are Flat Plate Precipitators?

A: An electrostatic precipitator (ESP) eliminates particles from a gas stream by utilizing electrical…

Q: OF HYDRAULIC CEMENT BY VICAT NEEDLE give example with solution ( i need example of this)…

A: data given   Time Vs penetration data is give  Initial setting time 33-35mm penetration At final…

Q: Room and Pillar Mining method

A: Room and piller method- Room and mining system in which the mined material is extracted across a…

Q: The pressure exerted on a 100x100 mm cube will be than that of a 150x150mm cube if a constant force…

A:

Q: What is the maximum permissible value (length x depth) for Applet on a rail vehicle wheel?

A: 7*1.5

Q: Provide a sample problem showing the figure and solution to show the mathematical application of a…

A: The mathematical application of a Three-Point Resection: Q. Determine the coordinates of an unknown…

Q: What is the difference between a roughage and a concentrate? Give an example for each category.

A: This question come from environment science engineering which is also sub part of the civil…

Q: Indian Standard (IS) Light Compaction test is usually conducted in 3 layers in a 1000 cc mould. How…

A: Given- IS Light Compaction Test- 3 layers in 1000 cc mouldfor 2250 cc mould number of blows per…

Q: Define the minimum curing period ?

A: The curing of concrete plays a very important role in the strength development of concrete. It…

Q: Define Schmidt hammer test can be adopted as an alternative test if concrete compression test fails?

A: The Schmidt hammer test is based on the elastic rebound of the hammer which presses on the concrete…

Q: Describe about the typical laboratory compression test?

A: A compression test is any test in which a substance encounters forces that move the specimen from…

Q: Q8. Estimate the production in compacted cubic yards per hour of a self-propelled tamping foot…

A: We will use formula of Volume.

Q: Describe about the results from consolidated–undrained (C–U) triaxial test and related strength…

A: The triaxial compression test is used to determine the shear strength of soil. It is commonly used…

Q: Describe about the vibrating plate compactors effectiveness.

A: Vibratory plate compactors:

Q: Tabulated Data and Result Specimen No. 1 2 3 Area of Bearing (in²) 4 4 ^ Maximum 200 205 210

A:

Q: Explain the difference between a rigid analysis and a nonrigid analysis.

A: Rigid analysis; Ultimate lateral strength can be calculated by using the rigid analysis. This…

Q: choose the correct answer When the transient gradient is decreased from the No. 200 sieve of the…

A: When the transient gradient is decreased from the No. 200 sieve of the bevel filler, a type shift…

Q: Define yield of cement in slurry design. 8.       Give the functions of centralizer and scratcher…

A: NOTE: Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Calculation: Compressive Strength (CS) = P/A Where: CS = compressive strength of the specimen, psi…

A: given- Gross Area data- Net Area data-

Q: Explain the reason why correction is applied in SPT test?

A: The field ‘N' value must be corrected before the SPT values may be used in design charts and…

Q: 2. What do the various elements that comprise the gating system? What are the function pouring basin…

A: As per guidelines we are supposed to answer only first questions, so please repost rest questions…

Q: Calculations of oedometer test Data Sheet: The results in the table have been obtained from the…

A: The coefficient of the compression index is the slope of the curve drawn between the void ratio and…

Q: 8) Explain briefly why the regions in the below given graph have curved boundaries rather than…

A: The given graph is a plot between stress/poisson ratio to deformation. Basically the linearity of…

Q: A SPT test was performed in a sandy soil layer (y = 115 pcf) at a depth of 16 ft. below the ground…

A: The given data is: γ=115 pcf Depth=10 ft SPT blow counts=1, 6, 5 N value =6+5              =11

Q: The crushed stone output from a 36-by 42-in. crusher, with a closed opening of 2 ½ in (output is 50…

A:

Q: How are wetting and drying SWCCs useful for geotechnical engineers in parctice applications.

A: Brief concept- SWCC- The relationship between matric absorption and water content is known as the…

Q: Explain the field procedure for injection grouting.

A: Grouting is usually carried out by driving pipes or boring holes into the ground, and then pumping…

Q: 6- What is the Mononobe-Okabe method, what are the assumptions of that method, the limitations of…

A:

Q: Define the term effective stress.

A: The combined effect of the pore water pressure and the total stress that keeps the soil particle…

Q: 100 kPa 25 kPa B. 25 kPa 75 kPa

A:

Q: What must be the minimum size (width) of chutes of the mechanical splitter if the dry fine aggregate…

A: For the dry fine aggregate in which the entire sample will pass the 9.5-mm (3⁄8-in.) sieve, a…

Q: DIRECT SHEAR TEST ON TIMBER SPECIMEN STEP Observation and Result. Width of the Thickness of the…

A: Shear strength parallel to grain is one of the common strength property determined for quality check…

Q: Question 4 During a consolidation test, the initial reading of the dial gauge is 450.0. The reading…

A:

Q: +Tabulated Data and Result, Modulus of Rupture Sample No. L (mm) b (mm) h (mm) 1 730 50 50 2 730 50…

A:

Q: uS. STANDARD SIEVE NUMOERS HYDROMETER 1 r e va 16 200 100 .001 100 GRAIN SIZEN MILLIVETERS Sample…

A: for graph 1 Type  - Sand Symbol -  SP SP-(poorly graded sand)

Q: functions of a drilling mud.

A: Drilling mud also called drilling fluid, in petroleum engineering a heavy viscous fluid mixture that…

Q: What is sieve analysis? State at least three (3) limitations of this procedure

A: Given data in question  Sieve analysis To be discussed  What is sieve analysis 3 limitations of…

Q: A bitumen sample was tested in the lab using Ductilometer apparatus, the sample was breaking at 90…

A: The ductility test on bitumen is done to determine its property and suitability for the construction…

Q: Standard Test Method for Ductility of Bituminous Materials   7) What is the effect of improper…

A: Note: We'll answer the first question since the exact one wasn't mentioned. Please resubmit a new…