A rigid bar is suspended by three rods made of the same material as shown in the figure. The area and length of the central rod are 3A and L, respectively while that of the two outer rods are 2A and 2L, respectively. If a downward force of 50 kN is applied to the rigid bar, then forces in the central and each of the outer rods will be LL 4 ilo P ons + 50 kN

A rigid bar is suspended by three rods made of the same material as shown in the figure. The area and length of the central rod are 3A and L, respectively while that of the two outer rods are 2A and 2L, respectively. If a downward force of 50 kN is applied to the rigid bar, then forces in the central and each of the outer rods will be LL 4 ilo P ons + 50 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F=30 kN single load, M=34 kN.m moment and w=10 kN/m distributed load are acting on the beam whose loading condition is given in the figure. Point B is located just to the right of the application point of force F and moment M. The length L is also given as L=5 m. According to this;Question1-A) Find the support response (Dy) at point D. (Write your result in kN.)Question1-B) Find the support response (Ay) at point A. (Write your result in kN.)Question1-C) Find the shear force (VB) at point B. (Write your result in kN.)
A cantilever beam, 3.5 m long, carries a concentratedload, P, at mid-lengthGiven:P = 200 kNE = 200 GPaI = 60.8 x 10^6 mm^4 How much is the deflection (mm)at mid-length What force (kN) should be applied at the free end to preventdeflection? To limit the deflection at mid-length to 9.5 mm, how much force(kN) should be applied at the free end?
Calculate the vertical reaction at support A. Enter your answer in kN to two decimal places.
The force acting on the gear tooth is 20 N. a. What gives the component of the force along line aa? b. What gives the component of the force along line bb? c. If the component of force F acting along line aa is 30 N, determine the magnitude of force F.
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
Consider two blocks connected . BlockA has mass 2.00 kg, and block B has mass 5.00 kg. The table on whichB sits is frictionless, the cord connecting the blocks is light and flexible,and the pulley is light and frictionless. The horizontal force F S hasmagnitude F = 20.0 N, and block B moves to the left with an accelerationof 1.50 m/s2. What is the coefficient of kinetic friction that one block exerts on the other?
Replace the loading (Figure 1) by an equivalent resultant force and couple moment at point O. Suppose that F1={8i−2k}kN and F2={−4i+5j−2k}kN. Part A Part complete Determine the resultant force. Enter the x, y, and z components of the force in kilonewtons to three significant figures separated by commas. Part B Determine the equivalent resultant couple moment about point O. Enter the x, y, and z components of the moment in kilonewton-meters to three significant figures separated by commas.
5. What is the approximate moment at support a? In kN.m A. -79.86 B. -27.95 C. -73.28 D. 0 E. -10.98 F. 73.28 G. 79.86 H. 10.98 I. 27.95
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers) Magnitude and direction Magnitude in lbs. Ax- Magnitude is 0 Ay- By-
Draw the free-body diagram of the foot lever shown.The operator applies a vertical force to the pedal so that the spring isstretched 1.5 in. and the force on the link at B is 20 lb.
For the beam and loading shown, specify (a) the absolute value of the reaction force in B in units |RB| kN, (b) the absolute value of the displacement at the midpoint D of the BC part of the beam in units |yD| mm. Take the P value in the question 15 kN and the W value 34 kN/m. E = 200 GPa and I = 34.4 x 10-6 M4.
Design a most economical spiral-column cross-section to support factored forces and end moments of Pu = 1,600 kips and Mu = 150 kip-ft. Assume that the centroid of the longitudinal bars from the edge of the column is 2.5 inch. Using the interaction diagram, how many #9 rebars will be used? Express your answer in whole number.