2. A rod hanging from a support whose unit mass is 3900 kg/ m has a cross sectional area of 400 mm? and 250 meters long. If the load of 18 kN is applied at its free end andE = 200 x 10° MPa, determine, a) Elongation due to its own weight in mm, b) Elongation due to the applied load in mm and c) Total elongation in mm.

2. A rod hanging from a support whose unit mass is 3900 kg/ m has a cross sectional area of 400 mm? and 250 meters long. If the load of 18 kN is applied at its free end andE = 200 x 10° MPa, determine, a) Elongation due to its own weight in mm, b) Elongation due to the applied load in mm and c) Total elongation in mm.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 14.8P: The small piston of a hydraulic lift (Fig. P14.8) has a cross-sectional area of 3.00 cm2, and its...

See similar textbooks

Similar questions

The total cross-sectional area of the load-bearing calcified portion of the two forearm bones (radius and ulna) is approximately 2.4 cm2. During a car crash, the forearm is slammed against the dashboard. The arm comes to rest from an initial speed of 80 km/h in 5.0 ms. If the arm has an effective mass of 3.0 kg and bone material can withstand a maximum compressional stress of 16 107 Pa, is the arm likely to withstand the crash?
Calculate the pressure due to the ocean at the bottom of the Marianas Trench near the Philippines, given its depth is 11.0 km and assuming the density of sea water is constant all the way down. (b) Calculate the percent decrease in volume of sea water due to such a pressure, assuming its bulk modulus is the same as water and is constant. (c) What would be the percent increase in its density? Is the assumption of constant density valid? Will the actual pressure be greater or smaller than that calculated under this assumption?
A suspender rod of a suspension bridge is 25.0 m long. If the rod is made of steel, what must its diameter be so that it does not stretch more than 1.0 cm when a 2.5104kg tuck passes by it? Assume that the rod supports all of the weight of the truck.
What effect does capillary action have on the reading of a manometer with uniform diameter? Explain your answer.
Is surface tension due to cohesive or adhesive forces, or both?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
By how much does a 65.0kg mountain climber stretch her 0.800cm diameter nylon rope when she hangs 35.0m below a rock outcropping? (For nylon, Y=1.35109Pa. )
A vertebra is subjected to a shearing force of 500 N. Find the shear deformation, taking the vertebra to be a cylinder 3.00 cm high and 4.00 cm in diameter.
Give an example of entrainment not mentioned in the text.
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
The small piston of a hydraulic lift (Fig. P14.8) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN?
The total cross-sectional area of the load-bearing calcified portion of the two forearm bones (radius and ulna) is approximately 2.4 cm2. During a car crash, the forearm is slammed against the dashboard. The arm comes to rest from an initial speed of 80 km/h in 5.0 ms. If the arm has an effective mass of 3.0 kg and bone material can withstand a maximum compressional stress of 16 107 Pa, is the arm likely to withstand the crash?