Solve it plz A round rod is made from a steel alloy with the details shownIn the figure. It is subjected to 3500 lb of tension. The Modulus ofElasticity is E = 30.6 x 106 psi.1 ft0.5 in.

Answered: Image /qna-images/answer/103c2339-4c7e-47e3-995f-14a1872fb028.jpg

Answered: A round rod is made from a steel alloy…

A round rod is made from a steel alloy with the In the figure. It is subjected to 3500 lb of tenslon. The Modulus of Elasticity is E = 30.6 x 106 psi. %3D 1 ft 0.5 in.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 29P: A structural member with a rectangular cross section as shown in the accompanying figure is used to...

See similar textbooks

Related questions

Q: The crate shown in Figure 2 is supported by a system of cables. Point A is in the horizontal x-y…

Q: 7. The horizontal stick of length, L, shown in the figure is uniform and weighs 200 N. Calculate the…

A: Length of the rod = L Weight of the rod = WL = 200 N Weight suspended = W = 500 N

Q: A steel bar is welded between two rigid surfaces as shown in the picture. The temperature of the bar…

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A: Given: The load P is 39078 N. The length of steel is 1.37 m. The length of bronze is 2.3 m. The area…

Q: 12. The concrete table column-support in Problem 20is reinforced with three -in steel rods, as shown…

Q: Bronze Steel A P

Q: The figure above is a skycam which is supported by 2 wires (assume that no wires holding at the top…

Q: Rods BC and DE are connected to an initially horizontal rigid bar CD, while rod AB is attached to…

A: Given:- Rods BC and DE are connected to an initially horizontal rigid bar CD, while rod AB is…

Q: Q2: A rigid bar is suspended from two wires of equal lengths 250 cm as shown below. Take E,= 210…

A: given data ,ES=210GPaEb=110GPalength =250cm1) FB+FS=10000N=10KN →(1)Now defoemation will be same…

Q: The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute t…

A: Solution: Given Data: The load W=80 kNThe tensile stress=50 MPaThe area of steel rod=300 in2The area…

Q: 2 For the assembly shown in the figure, brass rod AE (E=105 GPa) and aluminum rod BF (E=70 GPa) each…

A: To find displacement at point D

Q: A steel bar AD has a cross-sectional area of 0.40 in. 20.40 in. 2 and is loaded by forces P1=2700…

A: given data: P1=2700 lb P2=1800 lb P3=1300 lb Area =0.40 in2 a=60 in b=24 in c=36 in

Q: 1. Determine the deformation of the figure shown. Use E = 75 GPa. 30 mm 20 mm 30 kN 30 kN 400 mm

A: Given: Length of tapered Beam L= 400 mm Load acting on Beam P=30 KN Modulus of the elasticity E=75…

Q: A horizontal beam ABC is loaded as shown in the figure below. The distance of the point of contra…

Q: Q:2/A square steel bar is (50 mm) on a side and (250 mm) long. It is loaded by an axial tensile…

A: Given square bar side = 50mm 250mm long tensile force = 200kN E = 200 GPa and poisons ratio = 0.3

Q: A rigid steel bar is suspended horizontally by 1m steel rod at one end and 2m bronze rod at the…

Q: Q.3 A uniform steel plate 360 mm square with a mass of 25 kg is suspended in the horizontal plane by…

A: AB=3602+1202=379.5mm AC=300 mm BC=3602+1802=402.5 mm TA+TB+TC=25×9.8 =245 N ----(i) (summation of…

Q: Q.4.b. A compound bar is made up by connecting a steel member and a copper member rigidly fixed at…

A: Area of copper bar=A Area of steel bar= 2A for one half and A for second bar coefficient of thermal…

Q: A pin jointed frame is as shown in figure. Find horizontal displacement of joint J using the unit…

A: Pin jointed frame is type of structural framework with several components or members like channels…

Q: A bar obtained by bonding together pieces of aluminum (Ea = 70 GPa) and brass (E = 105 GPa) has the…

Q: A bar of 30 mm diameter is tested in tension. It is observed that when a load of 80 kN is applied,…

A: Given data:

Q: A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial load of 10 kN at…

A: Given: The diameter of the rod is 50 cm. The length is 6 m. The load is 10 kN. The unit weight of…

Q: A steel bar 1 in. square is 14ft long and has a modulus of elasticity of 29,000,000 psi. What total…

A: We know:Deformation =PLAEP=loadL=lengthA=areaE=modulus of elasticity of so,

Q: Replace the three forces which act on the bent bar by a force-couple system at the .support point A…

A: Ask to Replace the three forces which act on the bent bar by a force-couple system at the support…

Q: A rectangular beam carries a triangular load "w" as shown in the figure. Determine following…

A: Given data Uniformly varying Load on the cantilever beam. Width (B)=110 mm Height (H)=360 Modulus…

Q: 12. The concrete table column-support in Problem 20is reinforced with three -in steel rods, as shown…

Q: 5. A nail and a hammer are modeled by a linear spring and an incident mass according to the figure.…

A: To determine the maximum force between the hammer and the nail, and the duration of the impulse.…

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: First calculate the force in rod CD. Then calculate the elongation in the same. Then using similar…

Q: The cantilever steel beam as shown below has the rectangular cross section shown, determine the…

A: Given that:

Q: In the figure below, the horizontal bar ABC is supported by a pin at A and two rods with identical…

Q: A 30m tape weighing 0.90kg has a cross-sectional area of 0.0485cm2. The tape measures 30m when…

A: Given information: Length of the tape, L = 30 m Weight of the steel tape, W = 0.90 kg. Cross…

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Solution:-The diagram is shown below, Given data,Torque(T)=200kN.mE=720GPaG=27GPaThe diameter of…

Q: The prismatic block with dimensions a * b * c is placed in a rigid space of the same size. Find the…

A: Finding out the force to shorten the block by 2mm.

Q: The assembly in figure shown consists of two A-36 steel rods (E = 29 x 103 ksi) and a rigid bar BD.…

A: From the diagram FEF=10 kips +∑MB=0FCD2-101.25=0FCD=6.25 kip+∑MD=0100.75-FAB2=0FAB= 3.75 kip

Q: A steel bar 2.4 m long and 30mm square is elongated by a load 500kN. If passion's ratio is 0.25 and…

A: Given: The length of the square bar is 2.4 m. The side of the square is 30 mm. The load is 500 kN.…

Q: The figure below shows a thin-walled cold rolled steel cross-section. The thickness of all segments…

Q: A rigid bar of negligible weight is supported as shown below. Compute the value of the load W that…

Q: HOOP TENSION A cylindrical tank 1.40 m in diameter and 4 m high is full of liquid of specific…

A: Data Given: Diameter of the tank = 1.4 m Height of the tank = 4 m Specific Gravity of liquid = 0.78…

Q: Determine the stress in each section of the bar shown in the Figure when subjected to an axial…

Q: A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100…

A: Given:- A horizontal bar is fixed at one end i.e. at x = 0 The length of the bar = 1 m = 1000 mm…

Q: PROBLEM 1 Determine the load that can be applied at the end of the rigid bar if the stress in either…

A: K1 = 83 x 103 x 10^4/(8x150^3x20) =1.537 N/mm K2 = 13.5 N/mm 8Wx150/ πx10x10x10 + 8Wx120/ πx20x20x20…

Q: The steel block shown in Figure is subjected to a compressive force on all directions. Determine the…

Q: A rigid bar is supported by a spring as shown in the figure below. The deflection of the point C…

A: K=50N/m To find deflection at point C

Q: Replace the three forces which act on the bent bar by a force-couple system * .at the support point…

Q: A trapezoidal plate shown in the figure is submerged in water is 3.4 m below the surface. The bases…

Q: -Determine the maximum force P that can be applied without causing movement of the 90-kg crate that…

Q: Question 7 A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of…

A: The length of rod, L=2ft=24intenisle force, F=1000lbElongation, δ=0.009inModulus of elasticity,…

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

Q: P2. The coefficient of kinetic friction under block A is 0.30 and under block B is 0.20. Find the…

A: Given data, Kinetic friction for A = 0.30 Kinetic friction for B = 0.20 To find out the…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

Solve it plz

A round rod is made from a steel alloy with the details shown
In the figure. It is subjected to 3500 lb of tension. The Modulus of
Elasticity is E = 30.6 x 106 psi.
1 ft
0.5 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
An inverted cone is placed in a water tank as shown. If the weight of the cone is 16.5 N, what is the tensile force in the cord connecting the cone to the bottom of the tank? Refer to Figure no. 4.
A cylindrical tank of 10 mm thickness is filled with water that exerts an internal pressure of 3.0 MPa. Consider that the Poisson’s ratio is 0.30 and that the modulus of elasticity is 110 GPa. Calculate the change in diameter caused by the pressure of water if the inside diameter of the tank is 5.0 m.
In the Figure, the homogeneous block weighs 300 kg and the coefficient of friction is 0.45. If h = 50 cm, determine the force P to cause motion to impend. a.) 240 kg b.) 300 kg c.) 108 kg d.) 72 kg e.) None of the Above
The cantilever steel beam as shown below has the rectangular cross section shown, determine the maximum displacement of the beam use E=200 GPa for the modulus of elasticity 200mm 4 KN/m 6 KN .m 350mm 2m 2m 1m
Determine the change in the elastic energy of the spring as shown when it is stretched from: (a) position 1 to position 2, (b) position 2 to position 3, and position 1 to position 3. The spring constant is k = 100 N/cm . Additional information is as shown.
The rotating stepped shaft in the figure is produced from 85080M30 steel by machining method. It works at ambient temperature. If the force applied to the shaft is given as P=10 kN as constant, calculate the diameter d for the shaft to have an infinite life.(f=0.9) (Sut=600MPa)
In the figure, x=25cm initially. If the pressure at m is increase by 35 KPa while maintaining the pressure at n constant. Calculate the new value of x. Please provide explanation in every solution. Please be clear with your answer. Thank you.
The rigid bar shown in the figure is fixed to the top of the three posts made of steel and aluminum. The posts each have a length of 250mm when no load is applied to the bar and the temperature is T1=200C. Determine the force supported by each post if the bar is subjected to a uniformly distributed load of 120kN/m and the temperature is raised to 70°C. The diameter of each post and its material properties are listed in the figure.
3. Three bars each made from different materials are placed between walls when the temperature is 14°C. Determine the support reaction when the temperature becomes 19°C. The material properties are given in the figure Answer: R= 3502.30 N
Q3) when we put in the class tube have diameter 1.5 mm liquid with mass density900 kg/m3 , the liquid rise in the tube about 15 mm . Calculate the surface tension force?
Need answer ASAP. Please be detailed and clear with your solution. IV. The corner of a floating body has a quarter cylinder AB having a length normal to the paper of 3 m. 8) Calculate the magnitude of the horizontal component of the force on AB in kN. *9) Calculate the magnitude of the vertical component of the force on AB in kN. *