A bar obtained by bonding together pieces of aluminum (Ea = 70 GPa) and brass (E = 105 GPa) has the cross section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the horizontal axis.

A bar obtained by bonding together pieces of aluminum (Ea = 70 GPa) and brass (E = 105 GPa) has the cross section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the horizontal axis.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa
Steel 1 m Aluminum T 0.75 m Determine the maximum permissible value of T subject to the following conditions: tt S 80 MPa, Tal 50 MPa, and the angle of rotation of the free end is limited to 0.1 radian. For T. Hollow Solid d= 30 mm D= 40 mm %3D steel, G = 82 GPa and for aluminum, G= 28 GPa. %3D d = 30 mm %3D
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses oAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (SB) Brass: ab=20.9*10-6 1/°C, Eb=105GPA Aluminum: aal=23.9*10-6 1/°C, Eal=72GPA 60 mm diameter A 1.1 m B 40 mm diameter 1.3 m C Aluminum Brass
A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
The total tensile load of 160kN of a steel is to be stress at the middle portion limited to 150 N/mm2, find the diameter of the middle portion and also the length of the middle portion if the total elongation of the rod is to be 0.2mm. the length of the rod is 40 cm. consider the young modulus of a steel.
In the figure shown, the AB part of the rod is made from brass while the BC part is fabricated from aluminium, both parts are restrained at the ends. Find: 1) The normal stresses OAB and OBC + when the temperature is increased to 42°C. 2) The deflection at point B (8B) Brass: ab=20.9*10-6 1/°C, Eb=105GPA Aluminum: aa=23.9*10-6 1/°C, Eal=72GPA //// A 60 mm diameter 1.1 m B 40 mm diameter 1.3 m Aluminum Brass
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
5. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? -2 m- -1.5 m- 1.5 m- Bronze A = 300 mm2 E = 83 GPa L=2 m Steel A = 900 mm2 E = 200 GPa L = 1.5 m
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5