A sample of clay (weight = 13.2 N) is brought back from the field and trimmed to the following dimensions: height = 150 mm and diameter = 75 mm. The water content has been determined to be 25%. The Gs value for the solids is 2.75. Show and complete your phase diagram and find the following parameters: a. Draw a phase diagram b. Complete the phase diagram by finding the parameters of VT, Va, Vw, Vs, MT, Ma, Mw, and Ms. Volume should be expressed in the unit of m³ and mass in grams. Show all calculations to receive full credits. %3D

A sample of clay (weight = 13.2 N) is brought back from the field and trimmed to the following dimensions: height = 150 mm and diameter = 75 mm. The water content has been determined to be 25%. The Gs value for the solids is 2.75. Show and complete your phase diagram and find the following parameters: a. Draw a phase diagram b. Complete the phase diagram by finding the parameters of VT, Va, Vw, Vs, MT, Ma, Mw, and Ms. Volume should be expressed in the unit of m³ and mass in grams. Show all calculations to receive full credits. %3D

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.11P

See similar textbooks

Similar questions

A sample of saturated clay was placed in a container and weighed. The weight was 6N. The clay in its container was placed in an oven for 24 hours at 105˚C. The weight reduced to a constant value of 5N. The weight of the container is 1N. If Gs = 2.7, determine: a) Water Content b) Void Ratio c) Bulk Unit Weight d) Dry Unit Weight e) Effective Unit Weight
In the soil profile shown below, the water table is currently located at the ground surface (WT.1) and the clay layer has an OCR equal to 2.0. If the water table changes from level WT.1 to level WT.2 as depicted in the figure below, what is the new OCR in the middle of the clay layer a long time after the drawdown? (Acceptable tolerance = 2%, provide OCR value with 2 decimals).
A soil profile is shown in Figure P3.3 along with the standardpenetration numbers in the clay layer. Use Eqs. (3.8b)and (3.9) to determine the variation of cu and OCR withdepth. What is the average value of cu and OCR?
A soil specimen has a total volume of 70 cm3 and a total mass of 135.5g. After complete drying in an oven, the specimen has a mass of 122.0g. The Gs is 2.60. Determine the void ratio. Report your answer to three significant figures, and draw the full phase diagram.
The saturated clay sample was weighed in a container and the total weight was 7.4 N. 24 hours 105 degreesAfter waiting in the oven, the container was weighed again, this time it was measured as 5.6 N. The weight of the container is given as 0.7 N. Given the specific gravity of 2.66 for the soil, a) water content b) void ratio c) porosity d) density and e)Calculate the unit weight.
For a given soil, derive the following relation by drawing the three-phase diagram: γt = Gs γw (1 − n) + n S γw
1. A sample of saturated clay was placed in a container and weighed. The weight was 6 N. The clay withcontainer was oven dried for 24 hours at 105C and weighed again as 5N. if the weight of the containeris 1 N, and specific gravity of soil solids is 2.70, determine the a) water content b) void ratio c) bulk unitweight d) dry unit weight, e) saturated unit weight f) submerged unit weight. This is the question of Soil Mechanics.
A natural deposit of soil was found to have a water content of 27% and to be 88% saturated. Gs=2.7.Calculate (a) the void ratio, e; (b) the porosity, n; and (c) the dry density, ρd. (use kg/m^3 for density units). Include phase diagrams.
a wet sand sample has a volume of 4.6 x 10^-4 m^3 and weighs 8.1 N. After oven-drying, the weight reduces to 7.5 N. Use Gs=2.59. Calculate the degree of saturation in decimal form
From the constant head permeability test arrangement shown, the following values are given: Void ratio of specimen = 0.46 Length of Soil Sample = 450mm Constant head difference = 700mm Water collected in a period of 3 min = 0.000354 m3 Cross-sectional Area of Soil Sample = 0.00226 m2 Determine the coefficient permeability in m/hour (Ans: 2.102 m/hr) Compute the discharge of velocity in m/min. (Ans: 0.052 m/min) Compute the seepage velocity in m/min. (Ans: 0.165 m/min)
2. Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen = 16 cm Diameter of specimen = 96 mm Constant Head Difference = 50 cm Volume of water collected in 4 min = 420 cc Void ratio of the soil specimen = 0.55 a. Determine the hydraulic conductivity of the soil in m/min. Round off to four decimal places. b. Determine the discharge velocity in m/min. Round off to four decimal places. c. Determine the seepage velocity in m/min. Round off to four decimal places.
A sample of saturated clay from a consolidometer test has a total weight of 1.526 kg and a dry weight of 1.053 kg. The specific gravity of the solid particles is 2.7 1. Determine the water content. 2. Calculate the porosity. 3. Determine the total unit weight.