A sample of ocean sand was retrieved from 7 m below the surface. The sample had been under a vertical stress Ov of 150 kN/m³, a horizontal stress Oh of 250 kN/m³, a shear stress of 86.6 kN/m. If the angle theta between the vertical stress and the principal stress is 60°, calculate the angle of internal friction of the soil. [

A sample of ocean sand was retrieved from 7 m below the surface. The sample had been under a vertical stress Ov of 150 kN/m³, a horizontal stress Oh of 250 kN/m³, a shear stress of 86.6 kN/m. If the angle theta between the vertical stress and the principal stress is 60°, calculate the angle of internal friction of the soil. [

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.10P

See similar textbooks

Similar questions

Use Eq. (6.14) to determine the stress increase () at z = 10 ft below the center of the area described in Problem 6.5. 6.5 Refer to Figure 6.6, which shows a flexible rectangular area. Given: B1 = 4 ft, B2 = 6 ft, L1, = 8 ft, and L2 = 10 ft. If the area is subjected to a uniform load of 3000 lb/ft2, determine the stress increase at a depth of 10 ft located immediately below point O. Figure 6.6 Stress below any point of a loaded flexible rectangular area
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer. 2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
2. The state plane stress in a mass of dense cohesionless sand (c=0) is described by the following stresses: Normal stress on horizontal plane = 100 kPa Normal stress on vertical plane = 50 kPa Shear stress on horizontal and vertical planes = ± 30 kPa Determine by means of the Mohr circle the magnitude and direction of the principal stresses. Is this state of stress safe against failure assuming φ= 30o?
The following data are given for a direct shear test conducted on dry sand:- Specimen dimensions: 75 mm X 75 mm X 30 mm (height)- Normal stress: 200 kN/m2- Shear stress at failure: 175 kN/m2a) Determine the angle of friction,b) For a normal stress of 150 kN/m2, what shear force is required to cause failure?
he following results were obtained from a direct shear test conducted on pure sand: Sample height and diameter = 30 mm and 75 mm respectively. Normal stress = 100 kN/m2 Shear force at failure = 185 N a) Determine the angle of friction for the soil. Round off to one decimal i.e. 99.5! b) What would be the shear force (in N) at failure if the normal stress is 175 kN/m2? Round off to the nearest figure i.e. 300.55 to 301! c) What would be the principal stress at failure? Consider a and b
From the given soil formation of the soil with the following properties is shown in the figure. (see picture below) Compute the total stress at the mid-layer of the clay. (Answer: ) Compute the effective stress at the mid layer of the clay. If a load of 1800 kN is acting on the footing 2m x 2m is placed on the ground, find the stress increase at the mid layer of the clay assuming a stress distribution of 1 horizontal to 2 vertical. *unit weight of dry sand = 14.72 kN/m3*
A direct shear test, when conducted on a remolded sample of sand, gave the following observations at the time of failure: Normal load = 288 N; shear load = 173 N. The cross-sectional area of the sample = 36 cm2. Determine the minor principal stress in kPa. Show diagram
Can TRIAXIAL TESTS be performed on sand samples? Briefly explain. The results of an undrained triaxial test on a clay soil sample are given in table below Cell Pressure (kN/m2) 200 400 600 Additional Axial Load at Failure (N) 342 388 465 Each sample, originally 76mm long and 38mm in diameter, experienced a vertical deformation of 5.1mm. Evaluate the stress at failure for each cell pressure given in table above. Draw Mohr Circles and determine the shear strength parameters of the soil.
The soil profile shown consists of dry sand (4-m thick) which overlies a layer of clay (3-m thick). Ground water table is located at the interface of the sand and clay. a. If the water table rises to the top of the ground surface, what is the change in the effective stress (in kPa) at the bottom of the clay layer? Round off to two decimal places. (ANSWER: 26.336) b. Compute the effective stress at the bottom of the clay layer in kPa. Round off to three decimal places (ANSWER: 97.686) c. How many meters must the ground water table rise to decrease the effective stress by 14 kPa, at the bottom of the clay layer? Round off to two decimal places (ANSWER: 2.13)
From the given soil formation of the soil with the following properties is shown in the figure. (see picture below) Compute the total stress at the mid-layer of the clay. (Answer: 260.745 kPa) Compute the effective stress at the mid layer of the clay. (Answer: 147.93 kPa) If a load of 1800 kN is acting on the footing 2m x 2m is placed on the ground, find the stress increase at the mid layer of the clay assuming a stress distribution of 1 horizontal to 2 vertical. (Answer: 11.64 kPa) *unit weight of dry sand = 14.72 kN/m3*
The diagram below shows a multi-layered soil, write an expression for the stress at each layer and the vertical total stress at depth z. (all symbols have their usual meaning)
A triaxial test conducted on cohesionless soil gives the following results: Deviator stress at failure = 410kPa The angle of shearing resistance = 32 degrees Determine the following: a. Confining pressure in kPa b. Shear stress at failure plane in kPa c. Angle that the failure plane makes with the principal plane (degrees)