A security light system has a switch and a motion sensor attached. It can be either armed or unarmed. If the switch is in the off position, the light is off and the system is unarmed. When the switch is turned on, the light stays off but the system is armed. If the system is armed and the motion sensor detects movement, the light comes on. If no movement is detected for 5 seconds, the light goes off. Draw a UML state-chart diagram to describe the states of the security light system.

A security light system has a switch and a motion sensor attached. It can be either armed or unarmed. If the switch is in the off position, the light is off and the system is unarmed. When the switch is turned on, the light stays off but the system is armed. If the system is armed and the motion sensor detects movement, the light comes on. If no movement is detected for 5 seconds, the light goes off. Draw a UML state-chart diagram to describe the states of the security light system.

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter7: Arrays

Section7.5: Case Studies

Problem 15E

See similar textbooks

Similar questions

An electric ceiling fan has a pull rope as a switch. From off position when the rope is pulled, the fan will be in a slow speed condition. Second pull is medium speed option. Third pull is high speed option. Next pull the fan will be off.a. Draw state diagramb. Make table of state transitionc. Make the Boolean equation and simplifyd. Draw the circuit of FSM
Draw the state machine for a luggage belt system. The belt is started when the start button is pressed and runs until either the stop button is pressed or until there is no luggage detected on the belt for 60 seconds.
A friend would like you to build an “electronic eye” for use as a fake security device. Th e device consists of three lights lined up in a row, controlled by the outputs Left , Middle, and Right, which, if asserted, indicate that a light should be on. Only one light is on at a time, and the light “moves” from left to right and then from right to left , thus scaring away thieves who believe that the device is monitoring their activity. Draw the graphical representation for the finite-state machine used to specify the electronic eye. Note that the rate of the eye’s movement will be controlled by the clock speed (which should not be too great) and that there are essentially no inputs.
Which of the following is one of the three characteristics that are sought when it comes to the electrical power supplying IT equipment? Maximization of circulating current Reduction of the grounding circuit Increase in electromagnetism  Minimization of electrical noise Which of the following is a condition that must be met in order to qualify for the exemption from grounding requirements? The installation is in contact with ground and other conductive material. The runs are in lengths more than 25 feet long.  The circuits contain an equipment grounding conductor. The installation is guarded from contact by people. Installations of computer circuits for IT centers typically include isolated/insulated grounding circuits derived from power distribution units.  signal reference grids.  sensitive electronics.  broadband grounding systems.
traffic light is installed at a junction of a railroad and a road. the traffic light is controlled by two switches in the rails placed one mile apart on either side of the junction. a switch is turned on when the train is over it and is turned off otherwise. the traffic light changes from green (logic 0) to red (logic 1) when the beginning of the train is one mile from the junction. the light changes back to green when the end of the train is one mile away from the junction. all trains are less than 2 miles long. Draw circuit diagram
What if we construct the CPU but not the danger-detecting unit?
A robot system has a protective barrier enclosing the work cell area. The total time for the system to cometo a full halt after power is removed is 4 seconds, and an additional distance of 1.2 meter is required because of the height of the guard gate would allow operators to reach over it.Determine the minimum distance from the guard gate to the closed part of the robot work envelope, in meters NOTE: 1 meter = 1,000 millimeters
Draw a ladder diagram that will have the following results: a. Lamp L2 and Lamp L3 deactivated while Lamp L1 activated the moment power is turned ON. b. Lamp L1 and Lamp L3 deactivated while Lamp L2 activated when switch S2 is pressed and released. c. Lamp L1 and Lamp L2 deactivated while Lamp L3 activated when switch S3 is pressed and released. d. Lamp L2 and Lamp L3 deactivated while Lamp L1 activated when switch S1 is pressed and released.
Computer Science 1) Design a suitable code that toggles PORTD.6 which is connected to an alarm siren, whenever an external push button is pressed.
Implement a algorithm of a Failure Detector
Write a Step 7 program to control the following operations: 1. Place two parts in the feeding magazine (metallic and nonmetallic). 2. The ejector plate (Feed cyl) of the supply unit should push one part onto the conveyor. 4. The conveyor turns on and transfers the part past the sensor unit, where it is checked for type, to the stopper unit. 5. If the part is metallic, when it reaches the stopper, the conveyor stops, the z-axis cylinder goes down, the suction cup picks the part up, and then the z-axis retracts. The x-axis cylinder extends to drop the part onto the workpiece holding platform, while the cylinder is in the upper position (without lowering the z-axis). The x-axis retracts to the initial position.6. If the part is plastic, when it reaches the stopper, the conveyor stops, and the buzzer is turned on for a while then stops. 7. The process repeats. 8. Use the counters to count the different types of workpieces processed through the system.
Why the Normal temperature of computer is between 50 degree Fahrenheit to 82 degree Fahrenheit?