= A sequential network has one input and one output. The output becomes 1 when either M or N is detected in its input where M and N are binary numbers. Otherwise, it gives 0 in its output. Draw the state diagram for the following: 1. M = 11 and N=00 (use mealy model). 2. M = 01 and N=11 (use mealy model). 3. M = 10 and N = 1[(use mealy model). 4. M = 01 and N = 10 (use mealy model). 5. M = 01 and N = 10 (use moore model).

= A sequential network has one input and one output. The output becomes 1 when either M or N is detected in its input where M and N are binary numbers. Otherwise, it gives 0 in its output. Draw the state diagram for the following: 1. M = 11 and N=00 (use mealy model). 2. M = 01 and N=11 (use mealy model). 3. M = 10 and N = 1[(use mealy model). 4. M = 01 and N = 10 (use mealy model). 5. M = 01 and N = 10 (use moore model).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a combinational circuit with three inputs x, y and z, and three outputs A, B and C. When the binary input is 0, 1,2 or 3, the binary output is two greater than the input. When the binary input is 4, 5, 6 or 7, the binary output is three less than the input. Use Kmap to simplify and draw the correspondinglogic circuit diagrams of the simplified expressions.
(a) Using a decoder (3x8 line decoder as an Integrated circuit) and external gates, design the combinational circuit defined by the following three Boolean functions: F1 = x’yz’ + xz F2 = xy’z’ + x’y F3 = x’y’z’ + xy
A combinational circuit has four inputs (A,B,C,D) and three outputs (X.Y,Z). XYZ represents a binary number whose value equals the number of 1's at the input. For example if ABCD=1011, XYZ=011.(a) find the minterm expansions for X,Y, and Z.(b) find the maxterm expansions for Y and Z.
In a system with four-bit input, the input variables are A, B, C, D. A is the MSB. In this system, when variables B and C are 1 at the same time, the output is desired to produce 1 value. When this system is designed with the karnough map, which of the following is the simplified expression that will be obtained? A A'D' B B'D' C B'C' D BC E AD
(please do a and b sub questions) Design a combinational circuit with 4 inputs, A3, A2, A1, A0; and three outputs, X, Y, Z. The inputs represent a binary number in the range [0..15], and the outputs represent characteristics of the numbers. Specifically, X should be true if the number is divisible by 3; Y should be true if the number is prime; and Z should be true if the number is a power of 2. As an example, if the input is A3A2A1A0= 1100, this represents the number 12, which is divisible by 3, not prime, and not a power of 2 so the outputs should be XYZ =100. Recall that 0 is divisible by any integer. (a) Implement the circuit with AND gates, OR gates, and NOT gates. inverted inputs are OK. You may use the k-map template provided for your design work. You may use inverted inputs on gates. (b) Implement the circuit using AND, OR, NOT, and XOR gates. How much simpler is this design than the design in part (a)?
Design a combinatorial circuit that will be able to detect prime numbers given as input in binary. The input to the system will be any 4 bit binary number. The output of the circuit should be a single bit that will be 1 (high) if the input is a prime number and 0 (low) if the input is not a prime number. For example, if the input to the circuit is 0101 the output should be 1. Again if the input is 1010, the output should be 0.
The summing amplifier can be used as a digitallycontrolled volume control using the circuit shown. The individual bits of the 4-bit binaryinput word (b1b2b3b4) are used to control the positionof the switches with the resistor connected to 0V if bi = 0 and connected to the input signal vI ifbi = 1. (a) What is the output voltage vO with thedata input 0110 if vI = 2 sin 4000πt V? (b) Supposethe input changes to 1011. What will be thenewoutput voltage? (c) Make a table giving the outputvoltages for all 16 possible input combinations.
Range: n-bit unsigned and signed (2’s complement) numbers Complete the table:
2) Design a 2-to-1 multiplexer in which the inputs and outputs consist of single bits. Provide the truth table for this multiplexer using IN0 and IN1 for the two inputs, S for the select line and OUT for the output correctly. Obtain the minimal standard sum-of-products expression for the output correctly. PS: Number 2 will be used to help answer number 3 3) Obtain the schematic diagram for the mux designed in 2). Use proper conventions as to the labelling of part numbers, instance numbers and pin numbers correctly.
In a system with four-bit input, the input variables are A, B, C, D. A is the MSB. In this system, when A and D variables are 1 at the same time, the output is wanted to produce 1 value. When this system is designed with the karnough map, which of the following is the simplified expression that will be obtained? A B'D' B AD C BC D B'C' E A'D'
4. Design a combinational circuit with three inputs x,y,z and three outputs, A,B, C. When the binary input is 0,1, 2 or 3, the binary output is one greater than the input. When the binary input is 4,5, 6 or 7, the binaryoutput is one less than the input. Show truth table.
For the circuit (See image), complete the attached temporary diagram (Use the image). Explain your solution.Consider that the propagation times are negligible and that the setup and hold times are zero, so that the signals that change on the edge take the values defined immediately before the edge.