A shaft carries four masses in parallel planes A, B, C and D in this order along its length. The masses at B and C are 18 kg and 12.5 kg respectively, and each has an eccentricity of 60 mm. The masses at A and D have an eccentricity of 80 mm. The angle between the masses at B and C is 100° and that between the masses at B and A is 190°, both being measured in the same direction. The axial distance between the planes A and B is 100 mm and that between B and C is 200 mm. If the shaft is in complete dynamic balance, :determine The magnitude of the .1 masses at A and D The distance between .2 planes A and D The angular position of the .3

A shaft carries four masses in parallel planes A, B, C and D in this order along its length. The masses at B and C are 18 kg and 12.5 kg respectively, and each has an eccentricity of 60 mm. The masses at A and D have an eccentricity of 80 mm. The angle between the masses at B and C is 100° and that between the masses at B and A is 190°, both being measured in the same direction. The axial distance between the planes A and B is 100 mm and that between B and C is 200 mm. If the shaft is in complete dynamic balance, :determine The magnitude of the .1 masses at A and D The distance between .2 planes A and D The angular position of the .3

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Similar questions

A spacecraft must be maneuvered through an angle of 6O-deg in 30 s. The spacecraft moment of inertia is 8000 kg-m^2; the thrusters are located at a radius of 2.2 m from the center of mass. What is the minimum thrust level for the thrusters? Answer : 1.90 N. Don't give me wrong answers. correct answer is 1.90....show me how
.A steam engine develops power at mean torque of 18,000 N-m and velocity of 9 m/s. The mean diameter of the flywheel rim is 1.3 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
A shaft with 3 meters span between two bearings carries two masses of 10 kg and 20 kg acting at the extremities of the arms 0.45 m and 0.6 m long respectively. The planes in which these masses rotate are 1.2 m and 2.4 m respectively from the left end bearing supporting the shaft. The angle between the arms is 60°. The speed of rotation of the shaft is 200 r.p.m. If the masses are balanced by two counter-masses rotating with the shaft acting at radii of 0.3 m and placed at 0.3 m from each bearing centers, estimate the magnitude of the two balance masses and their orientation with respect to the X-axis, i.e. mass of 10 kg ‎‏Note: It must be solved using the graphic method, not the equations method.
A truck with four wheels, each 750 mm diameter, travels on rails round a curve of 75 m at a speed of 50 km/h. The total mass of the truck is 5 t and its centre of gravity is midway between the axles, 1.05 m above the rails and midway between them. Each pair of wheels is driven by a motor rotating in the opposite direction to the wheels and at four times the speed. The moment of inertia of each pair of wheels is 15 Kgm2. The rails lie on a horizontal plane and 1.45 m apart. Determine the load on each rail.
Charpy impact test pendulums are used to determine the amount of energy a test specimen absorbs during an impact (see ASTM Standard E23). The hammer weighs 71.2 lbs and has a mass moment of inertia about its center of gravity GH of 20.9 slug·in of 20.9 slug·in 2. The arm weighs 19.5 lbs and has a mass moment of inertia about its own center of gravity . The arm weighs 19.5 lbs and has a mass moment of inertia about its own center of gravity G.A of 47.1 slug·in 2. The pendulum is released from rest from an initial position of 0 = 39°. Knowing that the friction at pin O is negligible, determine (a) the impact speed when the hammer hits the test specimen, (b) the force on the pin O just before the hammer hits the test specimen,(c) the amount of energy that the test specimen absorbs if the hammer swings up to a maximum of φ = 70° after the impact.
The cranks and connecting rods of a four cylinder in-line engine running at 2000 rpm are 60mm and 240mm each respectively. The cylinders are spaced 150 mm apart. If the cylinders are numbered 1 to 4 in sequence from one end, the cranks appear at intervals of 90º in an end view in the order 1-4-2-3.The reciprocating mass for each cylinder is 15 kg. Determine (i) unbalanced primary and secondary forces, (ii) unbalanced primary and secondary couples with reference to central plane of the engine
Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
A 50 N force is applied 50 cm from the axis of rotation of a rigid body. The body starts from rest and completes 5 revolutions in 2.5 s. Calculate the Moment of Inertia of the body.
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 29cm, which carries a mass of reciprocating part whose magnitude is 11kgs with a revolving part of 5kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 500 from top dead centre to bottom dead centre. solve 4 and 5 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 41cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 76cm between the two cylinders in (N-m) 5. Magnitude…
The disk with a mass of 0.4 kg and a radius of 2 cm (I = 1 / 2mr ^ 2) slows down as it rolls on a flat surface. While the motion of the disc is the result of the moment of inertia, the friction coefficient is 0.1. Calculate the torque responsible for the deceleration of the disc
A shaft caries four rotating masses A, B, C and D which are completely balanced. The masses B, C and Dare 50kg, 80kg and 70kg respectively. The masses C and D make angles of 90° and 195° respectively with mass B in the same sense. The masses A, B, C and D are concentrated at radius 75mm,100mm,50mm and 90mmrespectively.The plane of rotation of masses B and C are 250mm apart. Determine the magnitude of mass A and its angular position the position of planes A and D.
A solid spare, a solid disk, and a thin hoop are all released from rest at the top of the incline (ho = 20.0 cm). a) without doing any calculations, decide which object would be spinning the fastest when it gets to the bottom. (Explain) b) again, without doing any calculations, decide which object would get to the bottom first. (Which one has greater translational speed?) think CoE. c) assuming all objects are rolling without slipping, have a mass of 2.00 kg and a radius of 3.00 cm, find the rotational and translational speed at the bottom of the incline of any one of these three objects.