A shaft is made of bronze at length AB and steel at length BC fixed at both ends. It is subjected to a concentrated torsional moment at the junction, The steel segment is 1 meter long. Assume that the Bronze has a diameter of 75mm, G = 35 GPa and τ = 60 MPa whilst the steel has a diameter of 50mm, G = 80 GPa, and τ = 80 MPa. What is the reaction at the left end if the maximum torque is applied to the saft, in kN.

A shaft is made of bronze at length AB and steel at length BC fixed at both ends. It is subjected to a concentrated torsional moment at the junction, The steel segment is 1 meter long. Assume that the Bronze has a diameter of 75mm, G = 35 GPa and τ = 60 MPa whilst the steel has a diameter of 50mm, G = 80 GPa, and τ = 80 MPa. What is the reaction at the left end if the maximum torque is applied to the saft, in kN.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.9.8P: A statically indeterminate stepped shaft ACE is fixed at ends A and B and loaded by a torque TQat...

See similar textbooks

Similar questions

.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
The non prismatic, cantilever circular bar shown has an internal cylindrical hole from 0 to y, so the net polar moment of inertia of the cross section for segment 1 is (7/8 )Ip. Torque Tis applied at _y and torque 772 is applied at .v = L. Assume that G is constant. Find the reaction moment Ry. Find internal torsional moments Tiin segments 1 and 2. Find x required to obtain twist at joint 3 of tf3 = TLtGIp. What is the rotation at joint 2, Draw the torsional moment (TMD:7(.,0 _v L) and displacement (TDD: M_y),0 x L) diagrams.
A statically indeterminate stepped shaft ACE is fixed at ends A and B and loaded by a torque TQat point C (see figure). The two segments of the bar are made of the same material, have lengths L4and LB, and have polar moments of inertia IAand Ipb. Determine the angle of rotation 4>of the cross section at Cby using strain energy. Hint: Use Eq, (3-55b) to determine the strain energy Urn terms of the angle d?. Then equate the strain energy to the work done by the torque to. Compare your result with Eq. (3-52) of Example 3-9.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
A shaft is made of bronze at length AB and steel at length BC fixed at both ends. It is subjected to a concentrated torsional moment at the junction, The steel segment is 1 meter long. Assume that the Bronze has a diameter of 75mm, G = 35 GPa and τ = 60 MPa whilst the steel has a diameter of 50mm, G = 80 GPa, and τ = 80 MPa.a) What is the ratio of the length of steel to the length of bronze such that the allowable stress in each material is reached simultaneously.b) What is the reaction at the left end if the maximum torque is applied to the saft, in kN.
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Polar Moment of Inertia of the Post?
Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T0 = 10 kN.m is applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm.
The A36 steel shafts as shown in the figure below are made from two segments: solid segment AC with diameter = 1 in and a hollow segment CB with an outside diameter = 2 in and inside diameter = 1 in. The shaft is fixed at both ends. Determine the magnitude of the applied torque T (lb-in) if the reaction at A is 600 lb-in clockwise.
mechanics of rigid bodies The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4x103 ksi and G brass at 5.2 x 103 ksi. with diagram if necessary.
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Angle of Twist in degrees?