#2. A compound wooden beam is connected together by a bolt at B. Assume that the connections at A, B, C, & D exert only vertical forces on the beam, the allowable tensile stress for the bolt is 150 MPa, the allowable bearing stress for the wood is 28 MPa, and the hole in the washers has the same diameter as the bolt. Determine the: a) Force exerted on the bolt (kN), b) Force exerted on the connection at C (kN), c) Diameter of the bolt (mm), and d) Diameter of the washer (mm). 2 kN 1.5 kN 3 kN -2 m 2 m-1.5 m--1.5 m-|-1.5 m--1.5 m- -15m D В

#2. A compound wooden beam is connected together by a bolt at B. Assume that the connections at A, B, C, & D exert only vertical forces on the beam, the allowable tensile stress for the bolt is 150 MPa, the allowable bearing stress for the wood is 28 MPa, and the hole in the washers has the same diameter as the bolt. Determine the: a) Force exerted on the bolt (kN), b) Force exerted on the connection at C (kN), c) Diameter of the bolt (mm), and d) Diameter of the washer (mm). 2 kN 1.5 kN 3 kN -2 m 2 m-1.5 m--1.5 m-|-1.5 m--1.5 m- -15m D В

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two forces P can be applied separately or at the same time to a plate that is welded to a solid circular bar of radius r. Determine the largest compressive stress in the circular bar (a) when both forces are applied, (b) when only one of the forces is applied.
A lap joint shown is made by two identical plates that are connected by nine 15-mm diameter rivets. The diameter of each hole is 18 mm. Assume that the force P is equally distributed among the rivets. (t = 20mm) A. What is the maximum force in Newton if the shear stress of the rivets is limited to 5 MPa and the bearing stress between each rivet and a plate is 6 MPa? B. If the force P-20 KN, what is the tensile stress in MPa at section a-a of the top plate?
A 150mm x 30mm x 250mm central wooden block is glued between cantilevered brackets 200mm x 50mm each as shown. If the Shear Stress of the glued joint can NOT exceed 4N/mm2, find the Vertical load that can be applied on the central plank.
The steel tie bar shown is to be designed to carry a tension force of magnitudeP=120 kN when bolted between double brackets at A and B. The bar will be fabricated from 20-mm-thick plate stock. For the grade of steel tobe used, the maximum allowable stresses are σ =175 MPa, τ =100 MPa,and σb=350 MPa. Design the tie bar by determining the required values of(a) the diameter d of the bolt, (b) the dimension b at each end of the bar, and(c) the dimension h of the bar.
5. A bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPa, in aluminum of 90MPa or in bronze of 100MPa.
Four plates, each being 15 mm thick, are to be connected by six bolts of 19 mm diameter as shown. Consider B = 181 mm. Assume that the force is equally distributed among the rivets. A. Determine the minimum force P (Newtons) if the allowable bolt shearing stress is 33 MPa. B. Determine the minimum force P (Newtons) if the allowable plate bearing stress is 32 MPa. C. Determine the tensile stress of the top plate (MPa) at segment a-a if the force P is 35 kN.
Calculate the largest weight W that can be supported by two wires. The stress in either wire is not to exceed 7.6 MPa. The cross-sectional areas of wires AB and AC are 150 mm2 and 250 mm2, respectively.Answer: W = ___________________
The homogeneous bar ABCD shown in figure below is supported by acable that runs from A to B around the smooth peg at E, a vertical cableat C, and a smooth inclined surface at D. Determine the mass of theheaviest bar that can be supported if the stress in each cable is limitedto 100 MPa. The area of the cable AB is 250 mm2 and that of the cableat C is 300 mm2.
A lever ABC is pinned at C and attached to a 12-mm diameter control cable AD. a. If the allowable tensile stress in the control cable is 140 MPa, what is the maximum safe value of the load P applied as shown in the diagram? b. What is then the shearing stress developed in the 20-mm diameter pin support at C? c. What is the bearing stress between the pin and the 25-mm thick support plates at C?
The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 295 MPa, determine the minimum bolt diameter that may be used in the connection.
A compressive load of 219 kN is resisted by a rectangular strut which has one side measuring 83 mm. If the stress in the strut is 164 909 kPa, what is the length of the other side of the strut?
The rigid bar ABC is suspended from three wires of the same material. The cross-sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P.