A ship with a displacement tonnage of 5600 tons is floating without an inclination, as KG = 5.5m and GM = 0.5m. is known. A 33-ton load on the center line inside the ship can reach 10m pier and 3m up being moved. In this case, in order to keep the ship inclined, a tank on the port side is used as starboard. Ballast water is transferred to a tank on the side. Horizontal distance between the volume centers of the tanks 6 m What is the amount of ballast water that needs to be transferred?

A ship with a displacement tonnage of 5600 tons is floating without an inclination, as KG = 5.5m and GM = 0.5m. is known. A 33-ton load on the center line inside the ship can reach 10m pier and 3m up being moved. In this case, in order to keep the ship inclined, a tank on the port side is used as starboard. Ballast water is transferred to a tank on the side. Horizontal distance between the volume centers of the tanks 6 m What is the amount of ballast water that needs to be transferred?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.11P: A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and...

See similar textbooks

Similar questions

Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen, air, and saturated steam at a temperature of 100C. Let D=1m,U=1m/sec, and hc=1W/m2K.
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
A loaded scow has a draft of 1.8 m in fresh water when erect. The scow is 6 m wide and 12 m long and 2.4 m high. The center of gravity of scow is 1.8 m above the bottom along the vertical axis of symmetry. What is the maximum single weight that can be moved transversely from the center of the scow and unloaded over the side without sinking the scow?
A loaded scow has draft of 1.6 m in sea water (sg = 1.03) when in upright position. The scow is 6 m wide and 12 m long and 2.4 m high. The center of gravity of the scow is 1.8 m above the bottom along the vertical axis of symmetry. Assume that the center of buoyancy is located half of the height of draft. What is the maximum single weight in kN that can be moved transversely from the center of the unloaded scow over the top edge without sinking the scow? (Considering rolling position)
Consider a flatboat hull which carries cargo down a river. When fully loaded the craft weight 150 kN. How far will this boat sink into the water? (i.e., What is boat’s “displacement, D?”) Be sure to draw a free-body diagram that shows all external forces operating on the boat; also, show all relevant dimensions. Locate the center of buoyancy (ycb) from the bottom of the hull. If the metacenter (M) is located at 0.98 m from the bottom of the hull, is this boat stable?
A ship having a horizontal sectional area of 7,065 m^2 at the waterline has draft of 12.35 m in salt water (s=1.03) while in fresh water draws 12.60 m. Find the weight of the ship with its cargo in MN indicate free body diagram
A loaded scow has a draft of 1.8m in freshwater when erect. The scow is 6m wide, 12m long, and 2.4m high. Its center of gravity is 0.6m below the top of the scow along the vertical axis of symmetry. What maximum single weight W can be moved transversely over the edge of the side without sinking the scow? Assume the center of gravity is at the same point.
A square gate (AB) mass (200 kg), resting on smooth bottom (B) and hinge at (A). For what water depth (h) will be the force at point (B) equal to zero? (Answer with sketch, See Fig.4)
A ship of displacement 36000 tonne carries oil fuel in four tanks 16.0 m long and 6.0 m broad, the tanks arranged with their length in the fore and aft direction. The specific gravity of the oil is 0.84, and the density of seawater inwhich the ship is floating is 1020 kgm-3. For a ship of this size, the metacentric height is at least 500 mm. What is the reduction of the metacentric height of the ship because of the oil that is contained in the tanks and how serious is this reduction? Please discuss further your conclusions.
Essay From the figure below, discuss the internal effect of the external forces acting on the body.
A tall open-topped standpipe has an inside diameter of 2,750 mm and a wall thickness of 6 mm. The standpipe contains water, which has a mass density of 1,000 kg/m3 . (a) What height h of water will produce a circumferential stress of 16 MPa in the wall of the standpipe? (b) What is the longitudinal stress in the wall of the standpipe due to the water pressure?
The dredger in Fig. P3.70 is loading sand (SG = 2.6) ontoa barge. The sand leaves the dredger pipe at 4 ft/s with aweight fl ow of 850 lbf/s. Estimate the tension on the mooringline caused by this loading process.