Gate AB in the figure below is 15 ft long and 8 ft wide into the paper and is hinged at B with a stop at A. The water is at 20 °C. The gate is 1-in- thick steel, SG =7.85. Compute the water level h for which the gate will start to fall. The specific weight of water-62.4 Ib/ft^3 Pulley 10,000 lb Water 15 ft 60°

Gate AB in the figure below is 15 ft long and 8 ft wide into the paper and is hinged at B with a stop at A. The water is at 20 °C. The gate is 1-in- thick steel, SG =7.85. Compute the water level h for which the gate will start to fall. The specific weight of water-62.4 Ib/ft^3 Pulley 10,000 lb Water 15 ft 60°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A vertical rectangular sluice gate at the bottom of the dam is 0.60m wide and 1.8m high and exposed to water pressure on one side corresponding to a head of 15m above itscenter. Assuming the gate on stem to weigh 2500 N and the coefficient of friction of the gate on runners to be 0.30, find the force necessary to raise it. Show your complete solution.
In Fig., gate AB is 5 ft wide into the paper, and stopB will break if the water force on it equals 9200 lbf. Forwhat water depth h is this condition reached?
Torricelli’s idealization of effl ux from a hole in the side ofa tank is V = √2 gh, as shown in Fig. P3.81. The cylindricaltank weighs 150 N when empty and contains water at20 °C. The tank bottom is on very smooth ice (static frictioncoeffi cient ζ ≈ 0.01). The hole diameter is 9 cm. For whatwater depth h will the tank just begin to move to the right?
A spherical tank of diameter 1.275 m and wall thickness 40 mm, contains compressed air at a pressure of 17 MPa. What is the absolute maximum shear stress?
A solid cylindrical needle of diameter d , length L , and densityρ n may fl oat in liquid of surface tension Y . Neglectbuoyancy and assume a contact angle of 0 ° . Derive a formulafor the maximum diameter d max able to fl oat in theliquid. Calculate d max for a steel needle (SG = 7.84) inwater at 20 ° C.
A hollow, pressurized sphere having a radiusr = 4.8 in. and wall thickness t = 0.4 in. is loweredinto a lake (see figure). The compressed air in thetank is at a pressure of 24 psi (gage pressure whenthe tank is out of the water).At what depth D0 will the wall of the tank besubjected to a compressive stress of 90 psi?
3. Supposed that air (std.) has a uniform density of 1.2kg/m^3, estimate how high (meters) above the sea level where there exists a zero pressure. Assume that in the given condition, barometric pressure at sea level is 101.325 kPa. Include also the free body diagram or figure of the problem, and your findings after solving it.
The surface tension of water in air is approximately 0.0072lbf/ft. If the atmospheric pressure is 14.7 psia, what is the pressure inside a droplet 0.5 mm in diameter?
Drive formula for increas in volume of a thin metalic sphere when if is subjected to an internal pressure P. If diameter of thin sphere is 400 mm, thickness, t= 2 mm and is just full of water at atmosphere. Calculate the volume of water pumped in to raise the inside pressure to 1.5 N/mm², E=100 kN/mm³, K=2.5 kN/mm², v=0.25.
In the Figure below, the cover gate AB closesa circular opening 80 cm in diameter. The gate is held closed by a 200-kg mass as shown. Assume standard gravity at 20 °C. At what water level (h) will the gate be dislodged? Neglect the weight of the gate. Specific weight of water 9790 N/m3
The 45 ° V-tube in Fig. contains water and is open atA and closed at C . What uniform rotation rate in r/minabout axis AB will cause the pressure to be equal at pointsB and C ? For this condition, at what point in leg BC will thepressure be a minimum?
Figure AB Cover rests on a flat surface. Cover 180 kg weight and 1.2 m wide. At what height is the water depth the lid won't open? find it. (glycerin density is 1260 kg/m3 , That density 1000 kg/m3 )