A shunt generator has an external characteristics whose terminal voltage given by the equation Vt=(250 - 0.4 IL), where IL is the load current. What current andpower will be supplied by the machine to a load resistor of 5.85 ohms?

By ohms law , Load current IL = Vt/load resistance RL. From above Vt= IL×R. Using above equation…

A shunt generator has an external characteristics whose terminal voltage given by the equation Vt3(250-0.4 IL), where IL is the load current. What current and power will be supplied by the machine to a load resistor of 5.85 ohms?

A shunt generator has an external characteristics whose terminal voltage given by the equation Vt3(250-0.4 IL), where IL is the load current. What current and power will be supplied by the machine to a load resistor of 5.85 ohms?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Related questions

Q: From the circuit below, determine secondary winding voltage Vsec if the primary winding voltage Vpri...

Q: 11 KVA single phase transformer has a voltage of 13.8 kV on the primary and 230 on the secondary det...

A: We need to find current on secondary side of transformer .

Q: Determine the voltage across 68kohms resistor for the shown network below if vi = 0.5Vdc Si Imax Vi ...

A: Silicon diode starts conduct when anode voltage is greater than cathode voltage by 0.7 volts.

Q: . Explain the successive approximation type ADC with neat schematic diagram.

Q: findd ľod these fanctions 228 12 5- 54 8- (Sta)(5+b)

Q: An open circuit has the following characteristics O a. zero Current, with voltage O b. with Current,...

Q: Vth=....2.V. Ra=..2. %3D Practical RL(Q) IL PL %23 96.4 77.7m 65.5m 25 50 75 is

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for y...

Q: Ql: Find the value resistance (R) for the circuit in figure 1.The power supply P=lk watt. Slon 우 8고 ...

Q: A 5-Ohm resistor is in parallel with a 20-Ohm resistor, is supplied by a 4-A current source. Calcula...

Q: Find the output voltage swing of the clipper circuit shown below.

A: As per the guidelines,we are supposed to answer only first question.Please repost the other one as n...

Q: Utilice el divisor de corriente para calcular la corriente que fluye hacia abajo a través de la resi...

Q: find the total voltage (VT) in the network * VI V2 V3 lov 5V 5V +1, VT O 20 O - 20 O 10

Q: if the potential difference equal (9 V) and resistance equal ( 150 n), the current for electric circ...

A: By ohms law , Current flowing through resistor= (Voltage across resistor)/resistance. Energy requir...

Q: rom the circuit below, determine V d.? (use the 2nd approximation Model) Np:Ns 6:1 120 Vac out 60 Hz...

Q: A series RLC circuit containing a resistance of 30Q, an inducta 0.25H, and a capacitor of 120UF are ...

Q: 3. If all initial conditions of the networks of Figure P1.3 are zero, find v(t),t>0 CONTINUOUS-TIME ...

Q: Find the second term of: (z+1)" Σ-(-1)n+1 n=1 n z+1 O no solution O {(z+1)^2]/2 O (z+1) ООО

Q: Calculate all currents flowing through resistors R,,R1 &R, by using Kirchhoff's Law. Ri=102 R3=52 R:...

Q: How does a multimeter identify BJT terminals?

A: First read all the functions of a multimeter carefully.

Q: From the figure below, determine the value of current I Si 무 10 V 10 2 A Si O 70mA O 140mA O 1A O OA

Q: Table 4.6. R2 100 ohms 12V R1 R4 1k ohm 470 ohms 330 ohms Figure 4.7 Table 4.2 Analyze the experimen...

Q: 1.31 A 3-phase 220 V, 50 Hz, six pole induction motor has the following parameters: r, = 0.252 x, =0...

A: In this question, 3 phase induction motor parameters are given. Find the stator current, output po...

Q: A phase modulator has kp =2 rad/V. What RMS voltage of a sine wave would cause a peak phase deviatio...

Q: if the potential difference equal (9 V) and resistance equal (150 N), the current for electric circu...

A: As per the company guidelines we can solve only one separate question , so please kindly post the re...

Q: To test a diode using analog multi-meter, you should use what function? a. dc voltmeter O b. ohmmete...

A: 1.Answer:a. Dc voltmeter To check whether diode is working or not we wil connect to Dc voltmeter mo...

Q: In a certain region of space, the electric field intensity has been measured to be: E(z,t) = 6 x10- ...

Q: Current can not flow through an insulator because they have O a. free electrons O b. no free protons...

A: The electrons in the insulator's atoms are strongly bonded, it means they have no free electrons so ...

Q: Solve L{t*u(t – 1) + 8(t – 1)}.

Q: find the total voltage (VT) in the network * V2 V3 It lov 5V 5V +1 VT

A: Kirchhoffs Voltage Law or KVL, states that the algebraic sum of all voltages within the loop must be...

Q: Sketch the transistor input and output characteristics of CE configuration and briefly explain the...

Q: Find the Laplace transform of the following: 1) tet-1u(t-1)

Q: dx = a dt + b dz (14.3) where a and b are constants. To understand equation (14.3), it is useful to ...

Q: R1 R2 v(1) (± i|(1) iz(1) |(1) L2

A: I am attaching detailed solution image of this question.

Q: Vtotal = 92 R = 286 What is the reading of voltmeter?

Q: Discuss the following statement “Since technology is evolving at an exponential pace, existing laws ...

A: Given, We have a statement. We have to discuss that . Please find the below attachment for the clear...

Q: 5 A 2ix 7 A 2 A(

Q: EQUIVALENT CICUIT DIAGRAM OF AN INDUCTION MOTOR OVER THE WOUND ROTOR INDUCTION MOTOR AND LABEL ON IT...

A: Principal of Induction motor When a AC supply given to the stator it generates a rotating magnetic f...

Q: Finol the Laplace treinsfor of figues below. | - 2- K 3-

Q: A 3 phase, 4 pole, induction motor has rotor resistance of 0.04 W per phase. The maximum torque occu...

Q: For the given system transfer function below, find the value of the rise time. 10 G(s) = %3D +44 Ans...

Q: From the figure below, determine the value of current I. 10Ω Si 12 V O 70mA O 1.13A O 1.2A O OA

Q: uestions 1- Calculate the number of samples per period when the information frequency signal is 1KHZ...

A: Signal frequency is 1 kHz and time period T=qmsec Sampling frequency(fs) will be 2f = 2 kHz fre...

Q: Q1) For the circuit shown in Fig. 1, find the current I30 and the average power. Let v(t) = 15 sin(w...

A: The circuit diagram is shown below, Where,V(t)=15sinωt+60°+10sin2ωt+30° VandI(t)=5 sinωt A

Q: Use a K-map to simplify the Boolean expression E = A'B C'D+A'CD + A'C' + C O E = A+ C OE= A' +C OE= ...

A: Given: The given Boolean expression E=A'B'C'D+A'CD+A'C'+C

Q: In the following figure, the coordinates (x, y, z) of the lattice point B with respect to the origin...

A: Answer -

Q: FOLLOW UP QUESTIONS: BIPOLAR JUNCTION TRANSISTOR (BJT) SOLVE FOR a.) IC(sat) b.) VCE(off) CONSTR...

Q: 2. (a) Determine voltage V, by Source shifting and Source transformation. 2A. 41 8/ 2Vx Ya寺io人

A: In this question, We need to calculate the value of voltage Vx as shown in the circuit.

Q: What is the voltage at node a for this ideal op amp configuration? R Ov, 10V R1 1kO R2 2k0 Vo 20V 20...

A: Given circuit, R1=1 kΩ=1000 ΩR2=2 kΩ=2000 ΩVo=-20 V

Q: he PIV rating of the diodes in a full-wave rectifier center tap must be larger than Vp O a. 0.636 O ...

Q: 122 3ov VxミYa Fig.4

Question

A shunt generator has an external characteristics whose terminal voltage given by the equation Vt=(250 - 0.4 IL), where IL is the load current. What current and
power will be supplied by the machine to a load resistor of 5.85 ohms?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
. When a self-excited compound DC generator supplies load, the terminal voltage is not the same as the generated emE Why? a) voltage drop across the armature resistance will reduce the voltage available at the load terminals b) where there is a series field, voltage drop across the series field resistance will reduce the voltage available at the load terminals c) both "a" and "b" d) neither "a" nor "b"
Dc machines A separately excited D.C. generator has an armature circuit resistance of 0.1 ohms. And the total brush-drop is 2 V. When running at 1000 r.p.m., it delivers a current of 100 A at 250 V to a load of constant resistance. If the generator speed drop to 700 r.p.m., with field-current unaltered, find the current delivered to load.
A compound DC generator has a series resistance divided equally and connected in series with the load and the armature. If this generator is rated at 720 V with an armature resistance of 0.1 Ω, shunt resistance of 240 Ω and a (total) series field resistance of 0.6 Ω, find the generated emf if it delivers 100 A?
A shunt generator has a no-load terminal voltage of 270 and a voltage of 245 when it delivers 180 amp. Assume a straight-line characteristic and determine the following: the voltage when the current is 120 amp and What is the equivalent load resistance under this condition?
A DC shunt generator supplies a load of 27 kW at 210 V through the cables of resistance, R = 126 mΩ. If the field winding resistance, Rf = 62 Ω and the armature resistance, Ra = 35 mΩ, Determine (a) the terminal voltage, and (b) the E.m.f. generated in the armature. The terminal voltage is = The E.m.f generated in armature is =
A shunt generator supplies a 20kW load at 200V through cables of resistance, R= 100mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =40mΩ, determine (a) the terminal voltage, and (b) the e.m.f. generated in the armature
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
A 50 kW, 220 V, dc shunt generators has an armature resistance including brushes of 0.026 ohms. If the shunt field resistance is 52 Ω. Find the induced emf at rated load.
Q2: A500 kW, 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when AT4 / pole = 208 AT. If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A.
14. A shunt generator has a no-load terminal voltage of 270 and a voltage of 245 when it delivers 180 amp. Assume a straight-line characteristic and determine the voltage when the current is 120 amp. What is the equivalent load resistance under this condition?
A 150-kW 250-volt compound generator is connected long shunt. If the shunt field resistance is 20 ohms, what is the series field-current at full load? (Ans.: 612.5 A) write diagram, given, etc