A500 kW, 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when AT4 / pole = 208 AT. If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A.

A500 kW, 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when AT4 / pole = 208 AT. If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.3P

See similar textbooks

Related questions

Q: 15. A 1500 kW, 550-V, 16 pole generator runs at 150 rev. per min. What must be the useful flux if…

Q: A long shunt compound dc generator delivers a load current of 69 A at 396 V and has armature, series…

A: First we will find shunt field current using following formula Ish =Vt/Rsh. For generator, Armature…

Q: )A 4-POle dc. shunt generator with a wave-Wound armature has to supply a Lamps each Load of 500 Iレ…

A: First we will find find armature current than we will find generated emf. Generated emf=∅×N×Z60×PA.…

Q: A shunt generator supplies a 50-kW load at 400 V through cables of resistance 0.2. If the field…

Q: Q4 A dc shunt generator 50 V at the load 6A, rotating 700 r.p.m at the torque 4 N.m. Find the…

A: The solution can be achieved as follows.

Q: 1- Power taken by the prime mover of an alternator in case of no-load goes to a. Produce power in…

Q: Of a shunt excited DA generator; Excitation winding internal resistance R = 2.5 e Armature winding…

Q: A lap wound dc generator having 50slots with 15conductors per slot generated at no led emf of 400v…

A: The detailed solution is attached with.

Q: please answer in bond paper 3. A long-shunt, four pole, 1500-W, 250-V, duplex wave-wound DC compound…

Q: dc shunt generator 50 V at the load 6A, rotating 700 r.p.m at the torque 4 N.m. Find the efficiency…

Q: Sketch the load characteristic of a d.c. generator with (i) shunt (ii) series excitation. Give…

Q: Q2) A 4 pole, lap wound, compound DC generator has an armature resistance of 0.2 Q, series field…

Q: .31 An 8-pole generator wave-connected conduct running at 400 r.p.m supplies a load of 12.52…

Q: A long-shunt d.c. compound generator supplies 25A at 90V. The resistance of armature, series field…

A: This is an easy question based on long shunt compound generator . In this we are having values of…

Q: Q1) A long shunt compound generator is supplying a load 100 A at a terminal voltage of 220 V. The…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 1- Power taken by the prime mover of an alternator in case of no-load goes to a. Produce power in…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: The terminal voltage of a 75-kW shunt generator is 600 V at rated load. The resistance of the…

A: NOTE: “Since you have asked multiple question, we will solve the first question for you. If you want…

Q: A long-shunt d.c. compound generator supplies 60A at 110V. The resistance of armature, series field…

Q: EAl 500 450 420 430 --------------- 400 300 200 100 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 4.75…

Q: r

A: The load characteristics of a DC generator gives us the information about the change in terminal…

Q: short-shunt connected compound DC generator delivers 219 A to a load at 250 V. Its shunt-field…

A: Voltage across shunt field winding= terminal voltage+ Drop in series field winding. Using ohms law…

Q: 1- A 220 V, 60 Hz, supply is connected to 200-turn armature winding of reluctance 1.7x10 At/Wb. Find…

A: The magnetic flux φ is given by the relation: EMF induced (E)=4.44×frequency (f)×Nos. of turns…

Q: ne function of a commutator is O change dc to ac O cuts the magnetic flux and emf is induced O…

Q: A non-salient pole, three-phase, Y-connected synchronous generator with synchronous reactance of Xs=…

A: Power delivered = sqrt(3)* Line to line voltage* armature current* power factor. EMF induced in…

Q: Example 26.20(a). A 4-pole, d.c. shunt generator with a shunt field resistance of 100 Q and mature…

A: Given data, Number of poles P = 4 Shunt field resostance Rsh=100 Ω Armature resistance Ra=1 Ω Number…

Q: A 220 V, 60 Hz, supply is connected to 200-turn armature winding of reluctance 1.7×10° At/Wb. Find…

A: A 220 V ,60 Hz,supply is connected to 200 turn armature winding of reluctance 1.7×105 AtWb .Find the…

Q: . The armature of a 6-pole separately excited dc generator is triplex wave wound with 534…

Q: A 20 kW, 440 V, long shunt, compound dc generator has a full load efficiency of 87 %. If the…

Q: The armature of a 6-pole separately excited dc generator is triplex wave wound with 534 conductors.…

Q: Q5) A 10 KW , 250 V, 6-pole lap-connected de separately-excited generator runs at 1200 rpm. Armature…

A: Given, Output power= 10 KW Voltage, V= 250 V Number of poles, P=6 As Lap wounded, so number of…

Q: A separately excited D.C. generator has armature circuit resistance of 0.1 ohm and the total…

Q: A four - pole DC long shunt compound generator with a wave wound armature, having 390 conductors,…

A: Since you have posted a question with multiple sub-parts, we will solve the first three parts for…

Q: Example 2.23 (H.W):- Two generators 1 & 2 are connected in parallel across two bus-bars to supply an…

A: Part (a): The circuit diagram is given by:

Q: Three separately excited DC generators are connected in parallei to sopply wcol fond current of…

Q: A separately-excited dc generator has no load output voltage of 120 V. its equivalent armature…

Q: B Q- A short a shunt d.e compound generator supplies- 200 A at 94V. The resistance of armature,…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: Example 29.2. A separately excited D.C. generator has armature circuit resistance of 0.1 ohm and the…

A: In this question we need to find a load current when generator running at 700 rpm

Q: A500 kW , 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of…

A: When brushes are on GNA (Geometrical neutral axis), then electrical angle (θe) =0° ATC/pole of a DC…

Q: A 500-V, wave-wound, 750 r.p.m. shunt generator supplies a load of 195 A. The armature has 720…

A: Due to commutator reaction de-magnetization happens, formula to calculate demagnetization turns per…

Q: Q2/ An eight poles DC shunt generator supplies a load of 12.5 ohm at 250 V. its armature carries…

A: We need to equivalent circuit and governing equations

Q: Q2: A500 kW, 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of…

A: the magnetic neutral axis usually shifts in the same direction as of generator and opposite in the…

Q: Q1// long shunt compound generator supplies 600 KW, 1200V shunt field resistance =75 0, armature…

A: As per the guidelines of Bartleby we supposed to answer first question only for solution of…

Q: Two separately excited DC generators are connected in parallel to supply a total loed of 300 A The…

A: Since there are multiple subparts, so I solve the 1st 3 subparts for you.

Q: Find the load angle and the components of armature current Id and Iq

Q: The flux per pole of a four-pole generator is 0.05 wb. It driven at a speed of 1500 rpm. In order to…

A: The solution can be achieved as follows.

Q: A 25 kW , 250 V long -shunt compound D.C. Generator running at 1000 r.p.m , the resistances of…

A: Given D.C long shunt generator V=250 v N=1000 rpm efficiency =80% iron and friction losses =3000 W…

Q: Example 2.23 (H.W):- Two generators 1 & 2 are connected in parallel across two bus-bars to supply an…

Q: a. Draw the connection diagram given in the question. b. Obtain the network voltage and the powers…

Q: Question-6 A non-salient pole, three-phase, Y-connected synchronous generator with synchronous…

Question

100%

Q2: A500 kW, 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when AT4 / pole = 208 AT. If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2: A500 kW , 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when ATd / pole = 208 AT . If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A .
A DC shunt generator supplies a load of 27 kW at 210 V through the cables of resistance, R = 126 mΩ. If the field winding resistance, Rf = 62 Ω and the armature resistance, Ra = 35 mΩ, Determine (a) the terminal voltage, and (b) the E.m.f. generated in the armature. The terminal voltage is = The E.m.f generated in armature is =
A shunt generator supplies a 20kW load at 200V through cables of resistance, R= 100mΩ. If the field winding resistance, Rf =50Ω and the armature resistance, Ra =40mΩ, determine (a) the terminal voltage, and (b) the e.m.f. generated in the armature
. When a self-excited compound DC generator supplies load, the terminal voltage is not the same as the generated emE Why? a) voltage drop across the armature resistance will reduce the voltage available at the load terminals b) where there is a series field, voltage drop across the series field resistance will reduce the voltage available at the load terminals c) both "a" and "b" d) neither "a" nor "b"
Dc machines A separately excited D.C. generator has an armature circuit resistance of 0.1 ohms. And the total brush-drop is 2 V. When running at 1000 r.p.m., it delivers a current of 100 A at 250 V to a load of constant resistance. If the generator speed drop to 700 r.p.m., with field-current unaltered, find the current delivered to load.
A dc shunt generator 50 V at the load 6A, rotating 700 r.p.m at the torque 4 N.m. Find the efficiency of generator?
A separately excited D.C. generator has an armature circuit resistance of 0.1 ohms. And the total brush-drop is 2 V. When running at 1000 r.p.m., it delivers a current of 100 A at 250 V to a load of constant resistance. If the generator speed drop to 700 r.p.m., with field-current unaltered, find the current delivered to load.
A 220 V , 60 Hz , supply is connected to 200 – turn armature winding of reluctance 1.7x105 At / Wb . Find the magnetizing reactance , the rms values of the ( magneto – motive force , exciting and armature currents , magnetic flux ) , and the inductance Draw the phasor diagram of the circuit .
111/ The armature reaction of the DC generator reduces the generated EMF. Select one: True False
A shunt generator supplies a 33kW load at 225V through cables of resistance, R = 100mΩ. If the field winding resistance, Rf =56Ω and the armature resistance, Ra =40mΩ. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
A 50 kW, 220 V, dc shunt generators has an armature resistance including brushes of 0.026 ohms. If the shunt field resistance is 52 Ω. Find the induced emf at rated load.
A short shunt compound generator has an armature; series field and shunt field resistances of 0.031Ω, 0.04Ω and 100Ω respectively. At rated load condition, the terminal voltage is 400V while the armature is developing an emf of 409V. Find the kW delivered to the load at rated condition.