A sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3 meters is observed. The bubble is then level through 7 spaces on the level tube, and the rod reading is 1.8 meters. One division in the level tube is equal to 0.6 mm. a. b. C. d. le. What is the sensitivity of the level tube? What is the radius of curvature of the level tube? What is the total distance moved by the bubble? What is the difference in rod readings? What is the subtended angle by the line of sights? type your answer... type your answer... type your answer... type your answer... type your answer... meters degrees seconds meters meters

A sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3 meters is observed. The bubble is then level through 7 spaces on the level tube, and the rod reading is 1.8 meters. One division in the level tube is equal to 0.6 mm. a. b. C. d. le. What is the sensitivity of the level tube? What is the radius of curvature of the level tube? What is the total distance moved by the bubble? What is the difference in rod readings? What is the subtended angle by the line of sights? type your answer... type your answer... type your answer... type your answer... type your answer... meters degrees seconds meters meters

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3 meters is observed. The bubble is then level through 7 spaces on the level tube, and the rod reading is 1.8 meters. One division in the level tube is equal to 0.6 mm. ASAP PLEASE What is the total distance moved by the bubble in seconds? What is the difference in rod readings in meters?
A rod is 60 m away from the instrument and the rod reading is 2.24 m. The bubble on the level tube was leveled through 5 spaces and the rod reading was 2.27 m. Determine the sensitivity of the level tube.
In a rectangular channel 4m wide with Q=7.65m3/s the depth is 0.4m. If a hydraulic jump is produced, (a.) what will be the depth immediately after it? (b.) what will be the loss of energy?
A sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3 meters is observed. The bubble is then level through 7 spaces on the level tube, and the rod reading is 1.8 meters. One division in the level tube is equal to 0.6 mm. c. What is the total distance moved by the bubble? Answer seconds d. What is the difference in rod readings? Answer meters e. What is the subtended angle by the line of sights? Answer meters Next QuestionNext
A calibration test of a 2.5cm circular sharp-edged orifice in the vertical side of the large tank showed a discharge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measurement of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. answers: a.0.989 b.0.636 c.0.629 d.0.98
8. Water flows into a vertical cylindrical tank at 12 ??³ /???; the surface rises in 6 ??/???. Find the radius of the tank.
A right-angled triangular notch is used for gauging the flow of a 140 cm wide, laboratory flume. In observing the head, a reading of 64mm was observed. Water passing over the weir drains into the basin of the hydraulic rig. 45cm in length and 30cm in width. At constant head, it took 27 seconds to fill a depth of 29cm in the basin. Actual discharge in the flume in cubic meter per second ? Theoretical discharge in the flume in cubic meter per second ? Compute for the coefficient of discharge of the notch
For a Gage Reading of 25.3 Kpa, determine the following: (a). Elevations of the liquids in the open piezometer columns E, F and G. (b). The deflections of Mercury in the U-tube manometer neglecting the weight of air.
A calibration test of a 2.5cm circular sharp-edged orifice in the vertical side of the large tank showed a discharge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measurement of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cc. Answers: a.0.636 b.0.989 c.0.629 d.0.98
2 - When the pitot tube is moved vertically inside the pipeline, why does it yield different flow velocities? Explain
Q3) A differential manometer is connected at two points A and B of two pipes. The pressure at A and B are 1 bar and 2 bar respectively. Find the difference in mercury level in the diffrential manometer. (12
Oil flows through a small standard 25m diameter orificce under a head of 5.4 m at the rate of 0.0031 m3/s. The jet strikes a wall 1.52 m away and 0.119 m vertically below the centerline of the contracted section of the jet. Compute the coefficient of velocity.