A signal with frequency 4935 Hz is sampled, and in the spectrum of the sampled signal there exist a guard band of 855 Hz between neighboring spectral components. Then the sampling frequency of the signal assuming that signal frequency is increased by 50% and guard band is decreased by 50% is. O 10083.75 11580.00 13620.00 O 15232.50

A signal with frequency 4935 Hz is sampled, and in the spectrum of the sampled signal there exist a guard band of 855 Hz between neighboring spectral components. Then the sampling frequency of the signal assuming that signal frequency is increased by 50% and guard band is decreased by 50% is. O 10083.75 11580.00 13620.00 O 15232.50

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the maximum signal frequency which can be recovered with sampling frequency of 9KHz? If for a signal f max=600Hz and f min=400Hz, what would be sampling frequency?
A bandlimited signal of max frequency 5 kHz is sampled. What will be the valuenof the Nyquist's sampling frequency?
The power of a signal is 10 mW and the power of the noise is 1 μW; what are the values of SNR and SNRdB ?
Explain through equations what happen if there is a phase error θc between the transmitted QPSK signal and local (replica) carrier signals in coherent QPSKdemodulator. Then what happen if θc=90o
6.1 A 1 kHz sine wave is sampled at frequency of 5 kHz.(a) What is the Nyquist frequency of the sampling system in this case? Showyour work.(b) What is the Nyquist rate of the signal? Show your work.(c) Is the signal properly sampled; that is, will there be aliases in the digitallyrecorded signal? Explain.(d) What if the original analog signal included both even and odd harmonics of itsprimary frequency; that is, 2, 3, 5 kHz, etc. What would be the highest harmonicthat will be faithfully represented in the discrete-time version of the analogsignal?(e) Following on with the previous step, what is the lowest harmonic that will bealiased and what would be resulting alias frequency?
2) An analog signal Xa(t) = sin(480pit)+3sin(720pit) is sampled 600 times per second . a) determine the nyquist sampling rate for Xa(t) and the folding frequency ? b)what are the frequencies in radians, in the resulting discrete time signals x(n) ? c)if x(n) is passed through an ideal D/A converter , what is the reconstructed signal Ya(t) ?
A base band signal used in European standard voice grade communication is represented by a band limited CT signal of triangular shape spectrum is sampled at fs=16 kHz. The spectrum of the sampled signal shows 4 kHz separation between the original signal spectrum and the next copy. (a) Find the maximum frequency in a CT signal. (b) Draw the spectrum of the sampled signal. (c) Find the cutoff frequency of the LPF used to recover of the original CT signal from the sampled signal. (d) Find the percentage of change in the sampling frequency from critical sampling.
A signal defined as x(t)=ejwot is periodic with a base period of T0=2π/w0. Is the X[n]=X(nT)=ejwonT signal obtained by sampling this signal with the time interval T periodic for the value T=T0/2, and if it is periodic, what is its basic period?
Which of the following is true about Signal-to-noise ratio? a. In linear codes, as the amplitude of a sample increases, SQR remains essentially constantb. SQR is inversely proportional with the amplitude of the signalc. SQR increases when the resolution is decreased.d. As the number of PCM bits increases, the SQR decreases
)A compact disc (CD) records audio signals digitally by using PCM. Assume the audio signal bandwidth to be 15 KHz, and the Quiantization level is 65536 a. What is the Nyquist rate? b. lf the Nyquist samples are quantized into L-65,536 levels and then binary coded, determine the number of binary digits required to encode a sample. c.Determine the number of binary digits per second (bits/s) required to encode the audio signal.
1. Given the bit pattern 01010111, encode this data using ASK, FSK, and PSK (i.e., draw the waveform that represents each ‘1’ and ‘0’). In the diagram, label amplitude values used in ASK, frequency values used in BFSK (Binary FSK because there are only 0s and 1s in data), and phase values used in BPSK (Binary PSK). Encode the same data using QPSK.
Design a 3rd order HPF without any kind of attenuation of ur original signal?