A signal x(1) has a spectrum shown below: X(f) -2 2 fikHz)) a) Sketch the spectrum of the sampled signal if f.=5 kHz. b) If a LPF is used with cutoff frequency f=3 kHz. Will the original signal be recovered? Sketch the LPF output signal. c) Repeat parts (a) and (b) if f.=3 kHz.

A signal x(1) has a spectrum shown below: X(f) -2 2 fikHz)) a) Sketch the spectrum of the sampled signal if f.=5 kHz. b) If a LPF is used with cutoff frequency f=3 kHz. Will the original signal be recovered? Sketch the LPF output signal. c) Repeat parts (a) and (b) if f.=3 kHz.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: FM signal has total power (72W), frequency swing(150 KHz) and the frequency of modulating signal is…

Q: Discuss the difference between frequency modulation and Amplitude Modulation. Elaborate the process…

A: Frequency Modulation Amplitude Modulation only carrier wave frequency varied only carrier…

Q: Given an AM DSBFC modulator with a carrier frequency of 100 kHz and maximum modulating signal of…

Q: A continuous time signal for a duration of 4s is uniformly sampled without aliasing and generating a…

A: Analog signals are transformed into discrete signals by sampling. The sampling theorem states that…

Q: 6.1 A1 kHz sine wave is sampled at frequency of 5 kHz. (a) What is the Nyquist frequency of the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Problem 2 Consider a sine wave of frequency fm and amplitude Am which is applied to a delta…

A: We need to tell about when slope overload error will accur. What will be maximum power is…

Q: A carrier wave of 100 MHz is frequency modulated by a 100 KHz sinewave with amplitude of 20 V, if…

A: Amplitude of modulating signal, Am=20 V frequency of modulated signal, fm=100 KHz modular…

Q: List 3 main differences of Analog Signal and Digital Signal

A: As per our guidelines we are supposed to answer only first question. Kindly repost the other…

Q: What are the circumstances in which a Kalman filter should be employed?

A: Kalman filter is designed in order to determine the future states of a given system by using the…

Q: 7. The signal to be digitized could occupy the range of 70 ± 10 MHz or from 60 to 80 MHz. Calculate…

A: Given Fmax= 80Mhz Fmin =60Mhz Bandwidth (B.w) = ? Sampling rate(Fs) =?

Q: 4. For an AM DSBFC modulator with a carrier frequency fc = 100 kHz and a maximum modulating signal…

A: Given, For an AM DSBFC modulator, Carrier frequency (fc)=100KHz Maximum modulating signal frequency…

Q: -VEE-VBE Rg+(1+B)[RE1+REZl i. Find gm, "x, Te- lB ii. Sketch the AC equivalent circuit and the…

Q: (a) You are required to implement a digital filter to suppress a high frequency noise disturbance.…

A: Introduction: Sampling is a process of reduction of a continuous - time signal to discrete time…

Q: What is the maximum signal frequency which can be recovered with sampling frequency of 9KHz? If for…

A: Sampling Frequency given by Fs=2× fmax Here fmax we have to find for 1st que and Fs is given as…

Q: The instantaneous value of the modulating signal to and FM modulator is -2V, sensitivity kf = 25…

Q: (c) If the carrier in part (b) has a peak-to-peak voltage of 12V and the modulating signal has a…

A: We need to find out the voltage for given amplitude modulation .

Q: A specific waveform of EEG signal comprises a frequency range up to 200 Hz. What is the minimum…

Q: receiver has a sensitivity of 0.3 μV, and the same receiver can handle a signal level of 75 mV…

Q: Question 2: The bandwidth of a signal is 5 kHz and we want to transmit it over a channel in PCM…

Q: Consider the analog signal x(t) = 3cos2000pit + 5sin6000pit + 10cos12000pit (a) What is the Nyquist…

Q: I signal (multiplexer output) for the multiplexer. Determine the bandwidth of the baseband signal…

Q: A) what name the modulation scheme in the blue curve in A and C B) what is the duty cycle in B C)…

A: solution a ) the modulation scheme in the blue curve in figure A = pulse position modulation (PPM)…

Q: a) You are required to implement a digital filter to suppress a high frequency noise disturbance. I.…

A: According to the guidelines solve first question Introduction Sampling is a process of reduction of…

Q: A digital communication link carries binary-coded words representing samples of an input signal…

Q: the order of the RC filter transfer function? 3rd 2nd 4th 1st 2. Why are unity gain…

Q: A base band signal used in European standard voice grade communication is represented by a band…

Q: d) Draw a fully labelled block diagram of a direct FM VCO modulator. Briefly discuss its operation…

Q: Explain what is meant by the term, modulation, and produce a diagram of an Amplitude Modulated…

Q: For an AM DSBFC modulator with a carrier frequency of 100kHz and a maximum modulating signal of…

A: We need to analyse the amplitude modulation .

Q: For a user signal with maximum frequency 20KHz: What must be the proportionality constant Kf and…

A: Given : Note : It is the kind notice that according to the guidelines of the company we supposed…

Q: Regarding phase modulation (PM), an increase in the PM index, µ, results in an increase in the…

Q: There are stations having the maximum frequency deviation of 75 kHz, and the maximum audio frequency…

A: As per our company guidelines we are supposed to answer only first one question. Kindly repost other…

Q: d by using a linear delta modulation (AM), the modulator has the fo e = 4 Fnyquist, where Fnyquist…

Q: Derive a relationship between the time constant RC, and modulation index.

A: Relationship between the time constant RC and modulation index. Input equation vi=Vi1+mcosωmt Here,…

Q: NBFM signal passes through a frequency multiplier. With β< 0.5 and fc=200kHz. Let fm ranges from…

A: If NBFM signal passes through a frequency multiplier. With β< 0.5 and fc=200kHz. Let fm ranges…

Q: A signal of 15 MHz is sampled at a rate of 28 MHz. What alias frequencies are generated?

Q: 6. The power amplifier of an AM transmitter has an output carrier power of 25 W and an efficiency of…

A: We need to find out audio power for given modulation index

Q: (a) What is the criterion for Carson's bandwidth calculațion?. b) List the advantagės modulation…

Q: Design a 3rd order HPF without any kind of attenuation of ur original signal?

A: To achieve the high-order high pass filter, it has to cascade the appropriate high-pass filter. To…

Q: For a square modulating signal with value 0 and 3 V entering an FM modulator with drift sensitivity…

Q: the frequency that is injected into an AM modulator is 100Mhz and it is combined with another…

Q: Q2. For the scheme shown in Figure Q2, i. Draw the spectrum of the baseband signal (multiplexer…

Q: q)what the advantages of using correlation measurements to improve signal detection?

Q: complex periodic analog signal, consisting of frequency fi and its harmonics, is to be sampled. The…

A: While sampling , a minimum frequency is required above which sampling is to be done. It is done in…

Q: The modulation index of the PM signal is 2. If a modulating signal that has amplitude of 50 mV at a…

A: Given Modulation index and amplitude of message signal for a phase modulation. We need to find the…

Q: 1 Can we generate FM signal using PM modulator? * Yes No

A: Yes we can generate the FM signal using PM modulator.

Q: The Nyquist sampling interval, for the signal sinc(700t) + sinc(500t) is?

Q: For a baseband signal, Fs = 4. 2fH K fH fH-fL K =

Concept explainers

Sample and Hold circuit

The sampling circuit and the holding circuit generate electrical samples as input and then hold these samples for a specified period. The time at which the sample and circuit holder produces the input signal sample is called the sampling time. Correspondingly, the length of the circuit that holds the sampled value is called the holding time.

Question

A signal x(t) has a spectrum shown below:
X(f)
-2
2
f(kHz))
a) Sketch the spectrum of the sampled signal if f=5 kHz.
b) If a LPF is used with cutoff frequency f=3 kHz. Will the original signal be recovered?
Sketch the LPF output signal.
c) Repeat parts (a) and (b) if f.=3 kHz.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the analog signalx(t) = 3cos2000pit + 5sin6000pit + 10cos12000pit(a) What is the Nyquist rate for this signal?(b) Assume now that we sample this signal using a sampling rate Fs = 5000 samples/s. What is the discrete time signal obtained after sampling?
(a) You are required to implement a digital filter to suppress a high frequency noisedisturbance.(i) Describe the precaution you would take in selecting the sampling interval(ii) How may the original signal recovered from the sampled signal?
Find the minimum sampling frequency for the bandpass signal whose frequency spectrum is given in the figure. plot the frequency spectrum of the sampled signal
6.1 A 1 kHz sine wave is sampled at frequency of 5 kHz.(a) What is the Nyquist frequency of the sampling system in this case? Showyour work.(b) What is the Nyquist rate of the signal? Show your work.(c) Is the signal properly sampled; that is, will there be aliases in the digitallyrecorded signal? Explain.(d) What if the original analog signal included both even and odd harmonics of itsprimary frequency; that is, 2, 3, 5 kHz, etc. What would be the highest harmonicthat will be faithfully represented in the discrete-time version of the analogsignal?(e) Following on with the previous step, what is the lowest harmonic that will bealiased and what would be resulting alias frequency?
What is the maximum signal frequency which can be recovered with sampling frequency of 9KHz? If for a signal f max=600Hz and f min=400Hz, what would be sampling frequency?
When does maximum frequency deviation occur in an FM signal? -It occurs during the transition of the modulating signal to the opposite sign. -It occurs at the maximum amplitude point of the modulating signal. -It occurs during the maximum rate of change of the modulating signal. -It occurs at the mean point of the modulating signal.
If the amplitude of the modulation signal voltage was given to be -4v and +4v and carrier amplitude also given to be -22v and +22v, by suitable waveform diagram determine the Am modulated output. Remember to provide all necessary wave forms in practical terms.
Discuss how the circuit produces a Frequency Modulated Signal
What is the period and frequency of this signal? Is the frequency constant?What is the bit rate of a given signal?What is the baud rate of a given signal?
1. What is the order of the RC filter transfer function? 3rd 2nd 4th 1st 2. Why are unity gain amplifiers used? To separate complicated chains in signal transmission into separate simple circuits To filter the signal To amplify the signal To “condition the signal” so there is no voltage dividers
An analog signal contains useful frequency component upto 100 hz what is nyquist rate for this signal? suppose we sample this signal at 250 samples/sec what is highest frequency component that can be reprensented uniquely at this sampling rate
What is a minimum number of sampling frequency required to have distortion free reconstruction of a digital signal from its samples?