A simple circuit of registors is shown in the figure. Here the components have values R, = 33.0 kQ R, = 33.0 kN R2 = 1.1 kN R4 = 1.1 kN and E.M.Fs E = 11 voltsE2 = 10 volts Note that E is not electric field . RI R2 Ry '3 B a)Write down the circuit equations involving currents and voltage drops in this circuit. One way to do this is to apply Kirchhoff's Voltage Rule (KVL). It is recommended that you draw circuit diagrams in your scripts and show current and circulation directions as you apply KVL. b)What is the current through R3 resistor? Absolute value of the current Give your answer up to at least three significance digits. A c)What is the voltage drop across R, resistor? Absolute value of the voltage drop Give your answer up to at least three significance digits. volts www

A simple circuit of registors is shown in the figure. Here the components have values R, = 33.0 kQ R, = 33.0 kN R2 = 1.1 kN R4 = 1.1 kN and E.M.Fs E = 11 voltsE2 = 10 volts Note that E is not electric field . RI R2 Ry '3 B a)Write down the circuit equations involving currents and voltage drops in this circuit. One way to do this is to apply Kirchhoff's Voltage Rule (KVL). It is recommended that you draw circuit diagrams in your scripts and show current and circulation directions as you apply KVL. b)What is the current through R3 resistor? Absolute value of the current Give your answer up to at least three significance digits. A c)What is the voltage drop across R, resistor? Absolute value of the voltage drop Give your answer up to at least three significance digits. volts www

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Estimate the dielectric losses in the solid specimen subjected to an alternating field of 40KV/cm, has an absolute permittivity of 4.445 x10-11 and the loss angle of that solid dielectric material is 0.28647at Oman power frequency. And also the same specimen while subjected to 3 KV/cm DC supply with the resistance value of 10 Mega Ohm, then determine the heat generated in the specimen.
can you please solve this question, thanks. Volume charge density is given by e-1000re-100z C/m3 . Find the maximum value of rv in the region 0 ≤ r ≤ 0.01 m, 0 ≤ f ≤ 2p, 0 ≤ z≤ 0.01 m.
Find the numerical value of the volume charge density at the point specified: D = rsinθcosΦ aθ C/m2 at PC(r = 1.5, θ =300, Φ = 500).
1.An aluminum wire having a radius of 8.97 mm and carrying a current of 6.43 mA is connected in a circuit. What is the drift speed of the electrons carrying this current? The density of electrons in an aluminum is 6.02×10^28 electrons/m^3. There is one conduction electron per atom in aluminum. Note: elementary particle charge e=1.602×10^−19 As Answer: __________ ×10^−8m/s 2. A potential difference of 14.99 V is applied across a wire of cross-sectional area 3.41 mm^2 and length 1,095 km. The current passing through the wire is 3.7 ×10^−3 A. What is the resistivity of the wire? Answer: _________ ×10^−8Ωm The temperature coefficient of resistivity for copper is 0.0068(C∘)^−1. If a copper wire has a resistance of 104 Ω at 23.26°C, what is its resistance 73.37°C? Answer: ________ V/m answer 1,2,3
The density of electrons increases along the coordinate (X) according to the following formula: n = 1028 + 5 × 1030 x + 4 × 1033 x2 .If the electron diffusion constant (D = 1.2 × 10-4 m2 / sec), calculate the diffusion current at a distance (x = 5mm).
Using the approximate field calculation in a cylinder-plane electrode system, extract the expression for the maximum electric field strength. Calculate the puncture voltage since the cylinder diameter is 24 mm, the electrode opening is 20 cm, the puncture strength of the air is 30 kV/cm and the correction factor (k) is 0.90
What are electron,hole,intrinsic carrier concentration, and energy band gap in si with (a) Nd= 4×10¹⁶ cm⁻³ and Na=1×10¹⁶ cm⁻³ and (b) additional 6×10¹⁶ cm⁻³ of ND ? Note: use Effective density of conduction band= 2.8 ×10¹⁹ cm⁻³ .Effective density of valance band =1.04 × 10¹⁹cm⁻³.T=300K ,Boltzmann constant = 1.38 x 10⁻²³ kgs⁻²K⁻¹
Use the following constants if necessary. Coulomb constant, k = 8.987×10^9 N⋅m^2/C^2 . Vacuum permitivity, ϵ0= 8.854×10^−12 F/m. Magnetic Permeability of vacuum, μ0 = 12.566370614356×10^−7 H/m. Magnitude of the Charge of one electron, e = −1.60217662×10^−19 C. Mass of one electron, m_e = 9.10938356×10^−31 kg. Unless specified otherwise, each symbol carries their usual meaning. For example, μC means microcoulomb .
A 8-volt battery is applied across a certain parallel-plate capacitor. If the capacitor was able to store 1.59 joules, determine the distance (measured in picometers) between the two plates of the capacitor. Both the plates have an area of 0.85 square meters. Express your answers accurate to four decimal places, whenever applicable. Assume the dielectric used for the capacitor has relative permittivity 1.83. Use the permittivity of free space to be 8.854 × 10-12 F/m.
The total charge entering a terminal is given by q = 2e3t cos (6\pi t), in µC. Determine the current at t= 0.25 s.
Calculate the electric field 5 cm outside a point charge of 10 nC in free space. Note that: ε0=8.85x10-12 Fm-1
Q6-Assuming that all of the valence electrons contribute to current flow, (a) calculate the mobility of an electron in copper and (b) calculate the average drift velocity for electrons in a 100 cm copper wire when 10 V are applied. Given( The lattice parameter of copper is 3.6151 10", copper is FCC, a = 5.89 x 105)