A simply supported beam ABC is loaded at the end of a bracket BDE (see figure).D(Use the deformation sign convention. When entering expressions, use the following as necessary: P and L.)Draw the axial-force diagram for ABC.NNState expressions for the minimum and maximum values of the axial force Mx).Nain =maxDraw the shear-force diagram for ABC.Vrur00State expressions for the minimum and maximum values of the shear force Vx).minV =maxDraw the bending-moment diagram for ABC.MMOMeenO OMinState expressions for the minimum and maximum values of the bending moment M(x).Mmin =%3D'max

All answers are marked with a rectangle in the image. Here the portion Ab alone will be experiencing…

A Simply supported beam ABC D 21/3 (Use the deformation sign convention. When entering expressions, use the following as necessary: Pand L.) Draw the axial-force diagram for ABC. Niguer Ng Ngn ONa State expressions for the minimum and maximum values of the axial force N(x). min N = %3D 'max Draw the shear-force diagram for ABC. Vron Vron Vr State expressions for the minimum and maximum values of the shear force Vx). Vein max Draw the bending-moment diagram for ABC. M OMan State expressions for the minimum and maximum values of the bending moment M(x). 'min M %3D max

A Simply supported beam ABC D 21/3 (Use the deformation sign convention. When entering expressions, use the following as necessary: Pand L.) Draw the axial-force diagram for ABC. Niguer Ng Ngn ONa State expressions for the minimum and maximum values of the axial force N(x). min N = %3D 'max Draw the shear-force diagram for ABC. Vron Vron Vr State expressions for the minimum and maximum values of the shear force Vx). Vein max Draw the bending-moment diagram for ABC. M OMan State expressions for the minimum and maximum values of the bending moment M(x). 'min M %3D max

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment = 20700 N-m Maximum negative moment = 2400 N-m Location of maximum shear from the left end of beam = 19 m Location of maximum moment from the left end of beam = 14 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Exercise caution in choosing the value of "c". (Be it known obviously that for beams with irregular cross-sections, Ctop ≠ Cbottom) Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
The simply supported beam in the figure is loaded by the clockwise moment 10 kN-m at B. Draw the shear force and bending moment diagrams by area method. Neglect the weight of the beam.Show complete solution with FBD
NEED IN 1HOUR PLS THANKS From the figure, compute for the horizontal and vertical component forces of the hinge at B acting upon member AC as shown.
Find axial force on member AE from the real structure in kN and absolute value of axial force on member ED from the virtual structure for the vertical displacement at joint B. Put (-) negative sign if its under compression. Use Virtual work method
The simply supported beam in the figure is loaded by the clockwise moment 10 kN-m at B. Draw the shear force and bending moment diagrams by area method. Neglect the weight of the beam.Please show complete solution
The simply supported beam in the figure is loaded by the clockwise moment 10 kN-m at B. Draw the shear force and bending moment diagrams by area method. Neglect the weight of the beam. Please give detailed solution and show also the elastic curve
The beam AC is simply supported at A and C and subject to the uniformly distributed load of 300 N/m plus the couple of magnitude 2700 N ⋅ m as shown in figure. Write the moment equation between A and C. Draw the shear and moment diagram. Determine the maximum shear and flexural stress of the beam with a rectangular cross section of 150mm x 250mm.
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. *USE 2 DECIMAL PLACES IN EVERY VALUES 1. What is the maximum shear of the beam in KN? (use two decimal places) 2. What is the maximum moment of the beam in KN.m? (use two decimal places) 3. What is the total cross-sectional area of the beam in mm2? (use two decimal places)
Solve the shear moment diagram of the beams using Method of Section ONLY. Show your step by step solution. C=200 KN ; D=200KN ; E=90KN Distance between C to B is 12 m. Distance between C and E is 2 m.A and B are reaction forces
Given: Maximum positive shear = 3960 N Maximum negative shear = 5640 N Maximum positive moment = 20700 N-m Maximum negative moment = 2400 N-m Location of maximum shear from the left end of beam = 19 m Location of maximum moment from the left end of beam = 14 m Determine the maximum bending stress (in MEGAPASCALS on the beam) given the cross-section on figure. Note: Measurements in figure is in millimeters. Kindly Draw the Shear and Moment Diagram or FBD if necessary. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
Assume that M0 = 5.90 kip-ft and L = 3.20 ft. Determine the reaction force at B. Assume that EI is constant for the beam. (Reminder: The roller symbol implies that both upward and downward displacement is restrained.)
In the figure, there is a joint at the C point in the AB beam, one end of which is fixed and the other end is held with a sliding support. Of beam its cross section is given below. To the beam, as shown in the figure between CB and 100 kN from point B An axial load of magnitude acts. a) Draw the bending moment diagram (influence line) and find the absolute maximum bending moment value. b) Where the absolute maximum moment found in (a) occurs, at point P shown in the cross section Determine the state of the stresses. c) Find the principal stresses and axes for the stress condition you calculated at point P.