A simply supported beam is carrying a uniform load. If the beam properties are givenbelow, what is the final stress at bottom of the beam section at midspan where the totallosses of the prestressing force is 21% (MPa)Properties:Beam width = 296 mmBeam height = 467 mmUniform load = 6.28 kN/mSpan of the beam = 10 mPrestressing force 310 kN%3Deccentricity = 110 mm

Answered: Image /qna-images/answer/90b8a958-854e-4608-bc6f-547dd4beb5ff.jpg

A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at bottom of the beam section at midspan where the tota losses of the prestressing force is 21% (MPa) Properties: Beam width 296 mm Beam height = 467 mm Uniform load = 6.28 kN/m %3D Span of the beam 10 m Prestressing force 310 kN eccentricity 110 mm !!

A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at bottom of the beam section at midspan where the tota losses of the prestressing force is 21% (MPa) Properties: Beam width 296 mm Beam height = 467 mm Uniform load = 6.28 kN/m %3D Span of the beam 10 m Prestressing force 310 kN eccentricity 110 mm !!

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at top of the beam section at 3.09 from the support. (MPa) Properties: Beam width = 259 mmBeam height = 447 mmPu = 63.85 kNSpan of the beam = 10 mPrestressing force = 502 kNeccentricity = 96 mm
A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and carries a concentrated load of 25 KN at the midspan. What is the maximum flexural stress of the beam? Blank 1 (use two decimal places)
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.41 from the support. (MPa) Properties: Beam width = 206 mmBeam height = 495 mmPu = 66.2 kNSpan of the beam = 11 mPrestressing force = 335 kNeccentricity = 105 mm
A beam width = 400 mm and height = 600 mm is subjected to a prestressing force of 200 kN at eccentricity = 150 mm. The beam with a length = 12 m is simply supported with loads of 10 kN/m in the entire length and a concentrated force of 50 kN. What are the stresses at the top and bottom at the centerline and at the points located at L/4 from the support?
The girder of a simple log bridge supports a wheel load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. Determine the maximum permissible wheel load W (in kN) based on an allowable shear stress of 0.75 MPa if the maximum shear stress on circular sections is 4/3 of the shear force divided by the cross-sectional Choices: 28.9 38.7 77.4 30.2 Note:please help me in this sample problem thank you
A 5-m simply-supported beam supports a uniformly distributed load equal to 40 kN/m applied throughout the beam. What is the maximum flexural stress if the beam has a rectangular cross-section with b = 300 mm and h = 600 mm? (in MPa) answer in 3 decimal places
A simply supported rectangular beam 50 mm wide by 100 mm deep, carries a uniformly distributed load of 1200 N/m over the entire length.1. Which of the following gives the max. length of the beam If the flexural stress is limited to 20 MPa. a. 3.11 m.b. 3.33 m.c. 3.44 m.d. 3.66 m.2. Which of the following gives the max. shearing stress of the beam. a. 0.30 MPab. 0.50 MPac. 0.40 MPad. 0.60 MPa3. Which of the following gives the max. deflection of the beam assuming E = 18000 MPa. a. 24.52 mmb. 25.72 mmc. 26.62 mmd. 28.82 mm
A brief, deep cantilever pillar is 500 mm long by 200 mm deep and is 2 mm thick. It carries a vertically descending load of 35 kN at its end. Expecting that the shear push is consistently dispersed over the cross area of the bar. Which of the following gives the uniform shear strain of the beam in radians if the shear modulus or Modulus of Rigidity G=25000 N/mm^2?
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
A beam having a span of 4m is subjected to a maximum shear of 20 kN. It has a triangular cross - section having a base width of 140 mm and an altitude of 300 mm. Which of the following gives the maximum shearing stress developed on the beam? a. 1.43 MPa b. 1.80 MPa c. 1.62 MPa d. 1.78 MPa
A 5-m simply-supported beam supports a uniformly distributed load equal to 40 kN/m applied throughout the beam. What is the maximum flexural stress if the beam has a triangular cross-section with b = 300 mm and h = 600 mm? (in MPa)