A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 252 lb/ft over its 19.3-ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel. Round off the final answer to two decimal places. www - 6 in. 10 in. 1/2 in. kol

A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 252 lb/ft over its 19.3-ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel. Round off the final answer to two decimal places. www - 6 in. 10 in. 1/2 in. kol

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Consider a wood beam (see figure) carrying a uniform load of 16.5 kN/m (which includes the weight of the beam). The length is 1.55 m and the cross section is rectangular with width 150 mm and height 300 mm. * Inserted Photo* If the beam is simply supported as in figure part (a), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ? MPa ?max= ? MPa (b) If the beam has a sliding support at right as in the figure part (b), calculate the maximum shear stress ?max and the maximum bending stress ?max. (Enter the magnitudes in MPa.) ?max= ?MPa ?max= ? MPa
The box beam in the figure is made of four pieces of wood nailed to each other as shown.Since the distance between the nails is 32 and the allowable cutting force on each nail is 160, (a=16, b=38, c=32, d=190, F=160) a) Maximum allowable vertical shear force in the beam? b) Determine the corresponding maximum shear stress in the beam.
shows the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the total ultimate load in kN concentrated at E induced by beam DEF using tributary area method.
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, w = 44 mm, and h = 75 mm . Round off the final answer to one decimal place.
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.14 in from the top of the beam on section 2.47 in to the right of B if P = 1042 lb, Q = 4278 lb, w = 1.1 in, L = 7.37 in, b = 3.82 in, and h = 0.73 in.
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
A plastic beam has a cross section with dimensions of a = 1.2 in., b = 4.2 in., d = 2.4 in., and t = 0.3 in. The centroid is located c = 1.015 in. above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is Iz = 2.384 in. 4. For a shear force of V = 2200 lb, what is the maximum shear stress in the beam?
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870
If possible, answer in 3 decimal places, thank you. For the wood beam shown in Figure A, assume L=1.5 m and P=8 kN. The beam cross section shown in Figure B has dimensions of b=47 mm and d=232 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? Calculate the reaction forces By and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown for the forces By and Dy on the free-body diagram below. (Note: Since Dx=0, it has been omitted from the free-body diagram.) By= kN Dy= kN Determine the shear forces VA⁢B, VB⁢C, and VC⁢D acting in segments AB, BC, and CD, respectively. Note that the shear force is constant in each of these segments. When entering your answers, use the shear force sign convention. VA⁢B= kN VB⁢C= kN VC⁢D= kN…
A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and carries a concentrated load of 25 KN at the midspan. What is the maximum flexural stress of the beam? Blank 1 (use two decimal places)