A single - break control is a?
Q: In |type of control system, controller gets the sampled error signal.
A: This is the question based on control syatem subject . In this the error sampled signal is present…
Q: 27. A closed-loop control system requires the sensing unit (i.e. sensor) to send the system. (a) no…
A: In this answer we will find the correct option to which a closed-loop control system requires the…
Q: Is it option B? 1. In an open loop control system the control action is dependent upon; a) the size…
A:
Q: Which of the following is not used in contactless detection? A) Magnetic sensor B) Pneumatic…
A: Pneumatic proximity sensors can additionally be used for the contactless sensing of iron (Fe) parts.…
Q: open-loop control system includes feedback of data related to the output of the process that is used…
A: In this question we will write about open loop control system....
Q: Determine in which part is the Power Control Circuit and Control Center.
A: A circuit diagram is given in the question. In the given schematic we need to determine which part…
Q: Define controllability in the control system.
A: Controllability in the control system define that all the state variables are input dependent. It is…
Q: or a Ladder Network Conversion, when will the control logic stop counting? When the staircase…
A: Although Ladder network conversion is method of analog to digital converter . block diagram for…
Q: Common selector switches are?
A: => Common selector switches, controls on and off of different current circuit by rotating the…
Q: Control Systems
A: According to question: The phase cross over frequency is calculated as
Q: * PLC is replacement of control panel .( ). True O False O Limit Switch is an Analogue input )…
A: To select correct answer from given options
Q: List the different types of Q-point stabilisation techniques and explain any one technique. Find Ico…
A: We need to list the different types of Q-point stabilization techniques and explain any one…
Q: In closed loop control system, that the system is unstable C the output has an effect upon the…
A:
Q: what are the major components of an electronic control system
A: In this case, the major components of an electronic control system needs to be identified.
Q: when using lm393, is it necessary to use a pull up resistor between the output and the power supply?
A: It is asked to discuss why we need to use a pull up resistor between the output and the power…
Q: How JFET manages to be operable when it doesn’t need biasing current
A: Junction field-effect transistors are the most basic type of field-effect transistor (JFET). They're…
Q: 5- Design and sketch a MOD-8 ripple-counter with manual reset push button.
A: The MOD-8 ripple-counter can be obtained from the MOD-16 counter. To design the MOD-8 up counter,…
Q: In an on/off control systems, to prevent rapid switching of control valve position an upper and…
A:
Q: a) Compare series, shunt, and chopper type JFET switch.
A: (a) FET can be used as a switch by operating it in two regions, they are cutoff and saturation…
Q: Digital Control process
A:
Q: Implement a 32:1 multiplexer using following instruction: 1-use a combination of 16:1 ,8:1 ,4:1…
A: A 32:1 MUX can be implemented by using two 16:1 MUX and one 2:1 MUX.
Q: Define observability in the control system.
A: Observability: The system is said to be recognizable if it is possible to measure all the state…
Q: 2 (а) Identify two (2) main components of a control valve
A:
Q: State and explain various test inputs 8n control systems.
A: In this question we will write about test signals..
Q: In type of control system, control signal is applied continuously through continuous feedback.
A:
Q: B) Differentiate between Shot, Thermal and Flicker noise.
A: The unwanted part of signal is called noise. Noise is equal to standard deviation of signal.…
Q: The ____ is an example of equipment that is operated by an automatic control system.
A: Given Data: The ____ is an example of equipment that is operated by an automatic control system.
Q: How Get = S+2 Rind the first order in control system and draw
A: Important Notes about first order system First order system can be described by first order…
Q: Which option is correct? 1. In an open loop control system the control action is dependent upon; a)…
A: ANSWER OPTION (a,b,c) is correct. ==> Open Loop Control…
Q: a) Identify the type of control system shown in given figure .Also define the type of control…
A: As per the guidelines, we supposed to answer one question at a time so please ask other questions…
Q: Explain briefly the process of setting up of the level instrument.
A: The process of setting up of the level instrument are < Set up the tripod at just above chest…
Q: State and explain various test inputs in control systems.
A: we need to find out state and explain various test inputs in control systems.
Q: An automatic pressure control system measured the output as 8 psi. If error signal is 5 psi, such…
A: In this question we will find set point with given error signal and output signal....
Q: QUESTION 1 Each of the signals P1C/P1D/P2B/CCP2, can be connected to more than one pin. Identify two…
A:
Q: List four of the Advantages /Disadvantages of Relay Control versus PLC Control ?? (Put the letter…
A: The explanation is as follows.
Q: Differentiate the Power Circuit over Control Circuit in DC Motor Controller.
A: Power Circuit : As any circuit that is used to carry the electricity that operates a load. Control…
Q: Explain QUADRATURE DETECTOR (FM Demodulator)
A: The FM quadrature detector and its affiliate or demodulator provide an alternative to a…
Q: 5) A Solid State Relay (SSR) can or should be used over a mechanical relay wher a) No mechanical…
A: A solid state relay is preferred over mechanical relay because of following reasons :- (a) the solid…
Q: Is option B the correct choice? 10. The output of a feed back control system is a function of a)…
A: Yes, option B is the correct choice. The explanation is provided below.
Q: The pointer moving across a scale in the speedo meter is an example for ___________ of the…
A: Analog instruments may be classified as primary instrument and secondary instruments. secondary…
Q: IV. Analysis 12V 9V 7.5V 6V 4.5V 3V. OV- Selector Switch 2 Poles/6 Position ✈ 00 2 3 LED's B+=? 1.…
A: Selector Switch : It is a switch that selects the desired port remaining other inactive by ohm's law…
Q: With the help of appropriate block diagrams explain briefly the difference between classical control…
A: In this questions we need to discuss about the classical and modern control system with block…
Q: control systems
A:
Q: the controlled signals in control BD are then going to Select one: O a. actuators O b. sensors O c.…
A: NOTE: We are authorized to answer the first question since the exact one wasn’t specified. Please…
Q: An automatic pressure control system measured the output as 8 psi. If error signal is 5 psi, such…
A: Given Output = 8 psi Error signal = 5 psi Set pint = ?
Q: Explain the construction and operation of instrument whose deflecting torque is proportional to the…
A:
Q: 1. Fill-in the blanks with the correct answer or chose the correct answer. the blue wire 1-3. Given…
A: Fill-in the blanks with the correct answer or chose the correct answer.
Q: Define the following: d)PD Controller e)Tuning of Controlle
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps