A single disc clutch with both sides of the disc effective has outside diameter of 250 mm and inside diameter of 150 mm. The applied force is limited to 20 kN based on axial pressure and the coefficient of friction is 0.25. Which of the following is the total torque that the clutch transmits? Assume uniform wear conditions. O 500 Nm O 510 Nm O 1000 Nm 2000 Nm

A single disc clutch with both sides of the disc effective has outside diameter of 250 mm and inside diameter of 150 mm. The applied force is limited to 20 kN based on axial pressure and the coefficient of friction is 0.25. Which of the following is the total torque that the clutch transmits? Assume uniform wear conditions. O 500 Nm O 510 Nm O 1000 Nm 2000 Nm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A disc clutch has 6 pairs of contacting friction surfaces. The frictional radius is 2 inand the coefficient of friction is 0.30. An axial force of 100 lb acts on the clutch. Theshaft speed is 400 rpm. What is the power transmitted by the clutch?
A soft surface cone clutch has an included angle of 20 degrees, a mean diameter of 12 inches, and a width of 4 inches. Using a coefficient of friction 0.2 and an allowable average pressure of 10 psi, deter the force required to engage clutch and the horsepower that can be transmitted at 500 rpm Ans. 560 lb, 14.4 hp
A multiplate disc clutch consist of a branz plate to transmit 10 kw at 1000 rpm di= 90 mm do= 160 mm friction coefficient =0.18 and the pressure is 0.3. find the number of contact surfaces.
In a lamella clutch, the number of inner lamellae zi= 5 pieces, the number of outer lamellas zd=6 pieces. If the inner radius of the lamella is ri=70mm, the radius of the outer lamella is rd=120mm, the surface safety pressure of the lamella material is pem =0.8 MPa, the friction coefficient is u=0.1, what is the maximum power that the clutch can carry at n=120 rpm?
A multi-plate clutch must transmit 11 kW of power without slipping at 1500 rev/min. The coefficient of friction is 0.3. The inner and outer radis are 30 and 85 mm respectively. The axial force applied to the plates is 780 N. Determine the number of plates required using.
A soft cone clutch has a cone pitch angle of 10°, mean diameter of 300 mm and a face width of 100 mm. If the coefficient of friction is 0.2 and has an average pressure of 0.07 N/mm2 for a speed of 500 rpm, find : (a) the force required to engage the clutch; and (b) the power that can be transmitted. Assume uniform wear. [Ans. 1470 N ; 10.4 kW]
The larger diameter and face of the disk of a multiple disk chutch are 225 mm and 20 mm respectively. The load applied to the spring of the clutch axially is 1500 N. Assuming that there are 8 pairs of friction 0.18 and tuning 800 rpm. Find the power transmitted by the clutch using uniform pressure method. (Ans, 13.67 kW)
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.
Question No.13: A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250mm and inner diameter is 150mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75kW at 500 rpm. Assume uniform wear and coefficient of friction as 0.3.
A friction clutch is to transmit 8kW at 2600 rpm. It is to be a single plate type with both sides of the plate effective, the axial pressure being limited to 0.09 N/mm2. The coefficient of friction is 0.3. If the external diameter of the friction lining is 1.4 times the internal diameter. By assuming uniform wear conditions analyze all the given parameters to determine the required dimensions of the friction lining
A multiple-disk clutch with 17 disks, 8 disks turning with one shaft and 9 with the other shaft, is rated at 25 hp at 500 rpm. The outside and inside diameters of the disks are 5½ and 2½ in., respectively. The coefficient of friction is 0.2. (a) Determine the axial force required to transmit the rated torque and determine the pressure between the disks.
A clutch functions to continue the power of 110 Hp and 3600 rpm rotation, number of clutch plate 1, The total force of the spring suppressor 1500 N, correction factor 0.95 and friction coefficient 0.3 Calculate the Measures of Do and Di if the ratio of Do: Di = 3: 2