A single-phase full-wave controlled rectifier using center tap transformer is fed from a 220 V, 50 Hz ac source and it is connected a resistive load R = 20 Q. Determine (a) draw circuit diagram, (b) the output voltage and current, (c) form factor, (d) ripple factor, (e) efficiency. Consider delay angle is a = 45° and turn ratio of transformer is 5:1.

A single-phase full-wave controlled rectifier using center tap transformer is fed from a 220 V, 50 Hz ac source and it is connected a resistive load R = 20 Q. Determine (a) draw circuit diagram, (b) the output voltage and current, (c) form factor, (d) ripple factor, (e) efficiency. Consider delay angle is a = 45° and turn ratio of transformer is 5:1.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

What is a disadvantage of an autotransformer?
A single phase full-wave controlled rectifier using center-tap transformer is fed from a 230 V, 50 Hz ac source and it is connected to a resistive load R=10Ω. Determine (a) the output voltage, (b) form factor, (c) ripple factor, (d) rectifier efficiency, (e) transformer utilization factor at = 30o. Turn ratio of transformer is 1 : 1.
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
An ideal single-phase full wave rectifier circuit has a non-inductive resistanceload, negligible tube drops and no transformer losses. What is therectification or conversion efficiency in percent?
A step-down delta-star transformer, with per-phase turns ration of 5, is fed from a 3-phase, 1100 V, 50 Hz source. The secondary of this transformer through a 3-pulse type rectifier feeds a R load of 10 Ω. Find the maximum value of the load current (phase).
Suppose line voltage may be as low as 105 Vrms or as high as 125 Vrms in a half-wave rectifier. With a 5;1 step-down transformer, the minimum peak load voltage is closest to___
i) Draw the circuit diagram of the single phase full wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation. (ii) A single phase fully controlled bridge rectifier circuit has DC output voltage 175 V for an AC supply voltage of 210 V rms. Find the firing angle delay of the circuit for the following cases (a) Converter mode (b) Inverter mode
A single-phase center-tapped transformer rectifier has an ac source of 240 V rms and 60 Hz. The overall transformer turns ratio is 3:1 (80 V between the extreme ends of the secondary and 40 V on each tap). The load is a resistance of 462 Ω. Determine (a) the average load current, (b) the rms load current, (c) the average source current, and (d) the rms source current. Sketch the current waveforms of the load and the source
To control a bipolar stepper motor by an Arduino: a. We use an H-bridge as an interface between the Arduino and the motor. b. We connect the motor directly to the Arduino. c. We use a Darlington array as an interface between the Arduino and the motor.
A two-winding, step-down transformer has a turns-ratio (N2/N1) of 0.5. The primary winding resistance and reactance are 2.5Ω and 6Ω, whereas the secondary winding resistance and reactance are 0.25Ω and 1Ω, respectively. Its magnetizing current and core-loss current are 51.5 mA and 20.6 mA. While in operation, the output voltage for a load of 25 /_ 300 is found to be 50 V. Determine the supply voltage, the current drawn from the supply and the power factor. ...
a half-wave rectifier circuit in the figure below has a transformer inserted between the source and the remainder of the circuit. The source is 240 Vrms at 60 Hz, and the load resistor is 20 ohm. (a) Determine the required transformer turns ratio (Ns/Np) so that the average load current is 12 A. (b) Determine the average current in the primary winding of the transformer.