A single-phase, half-bridge inverter feeds a resistive load, R = 10 Ohms. If the source voltage is 240 V, determine (a) the RMS value of fundamental component of output voltage, (b) the output power, (c) the peak off-state voltage across each semiconductor switch, (d) the lowest-order harmonic and the corresponding harmonic factor, and (e) the RMS and average values of currents through semiconductor switches

A single-phase, half-bridge inverter feeds a resistive load, R = 10 Ohms. If the source voltage is 240 V, determine (a) the RMS value of fundamental component of output voltage, (b) the output power, (c) the peak off-state voltage across each semiconductor switch, (d) the lowest-order harmonic and the corresponding harmonic factor, and (e) the RMS and average values of currents through semiconductor switches

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

q: A singal phase half bridge inverter has (R=2.4 ohm) and (dc) input voltage is (dc=48 v) DETERMINE: 1- The rms output voltage at the fundamental frequency? 2- the output power? 3- the avrage and peak currents of each transistor? 4- the peak reverse blocking voltage of each transistor? 5- The avrege supply current? 6- The total harmonic distortion (THD)? Note: please type it>>
1. A single phase half-bridge inverter, connected to 230V dc source, feeds a resistive load of 10Ω. Determine (a) fundamental rms output voltage (b) total output power and fundamental frequency power (c) average and peak currents of switches (d) input pf. 2. Discuss 1200 mode of conduction for a 3ph-phase VSI. Also, derive the expression for the outputvoltage and draw waveforms for phase voltages, line voltages and voltage across one switch.
A resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. EVALUATE Fundamental component of load voltage and fundamental component of load current;
A resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. Sketch the waveforms of load voltage, fundamental component of load voltage, fundamental component of load current, current through any one device and voltage across any device .
A resistive load of 30Ω is connected to an IGBT based Single-Phase Half-Bridge Inverter.The DC source voltage Vs=120V. EVALUATE THE Output voltage (rms value) and peak voltage across the device at OFF state;
1 phase half bridge inverter having dc input voltage 300V , and purely resistive load R = 2.4 ohm , find :Vrms for the first harmonic fundamental load power: average supply current if the power delivered by each source is 3.8 kw :
1. In a full-bridge single-phase inverter with an input voltage of 200V and a switchingfrequency of 4kHz, the power of a 16Ω load is controlled by the method of a gappedsquare wave control. Ignoring the circuit losses, answer the following questions a. Draw the inverter circuit presented in the question b. Generate PWM signals for a duty ratio of ½. Draw the load voltage, load current. Drawthe current and the voltage of any of the semiconductors. Find the load voltage. Find theoutput voltage frequency c. Find the nominal (the maximum) power and current of the load d. Find the duty ratio to get half of the nominal voltage e. Find the duty ratio to get a quarter of the nominal power f. Find the average value and effective value of BJT current for the case of item-e
A DC link inverter has an AC rms line input of 600 V, 50Hz. The inverter load is a balanced star connection of 195Ω resistors.Determine load current and power for a converter firing angle delay ofa) Determine load current, voltage and power for a converter firing angle delay of 12.5 degrees.b) Determine load current, voltage and power for a converter firing angle delay of 62 degrees.
For a single phase inverter has the following parameter ;Vdc = 80v , R = 8Ω , L = 20mH and F = 60Hz , Determine totalharmonic distortion for n = 5 then write expression for voltage
Single-phase full-bridge inverter is connected between a 200 V d.c. source and a series connected R-L load with R = 20Ω and L = 50 mH. The inverter frequency is 50 Hz. Determine the values of the rms load current, the load power and the total harmonic distortion factor, up to the 9th harmonic.
The single-phase half-bridge inverter has a resistive load of R = 2.4Ω and the DCinput voltage is 48V. Determine:1- the rms output voltage at the fundamental frequency2- fundamental displacement factor .3- fundamental power , drown from each source .4- fundamental load power .5- total power drown from each source .6- total load power .
A DC bus connected to a three-phase inverter is rated at 800V and the output voltage produced by the inverter has an rms value of 240 V. What is the modulation index? ...