A single phase half-wave rectifier is connected to a 100V RMS 50Hz AC supply. If the rectifier is used to supply a resistive load of 250 Ohms. Calculate: 1. maximum voltage amplitude. 2.the equivalent DC voltage developed across the load. 3.the load current. 4.power dissipated by the load. Assume ideal diode characteristics.

A single phase half-wave rectifier is connected to a 100V RMS 50Hz AC supply. If the rectifier is used to supply a resistive load of 250 Ohms. Calculate: 1. maximum voltage amplitude. 2.the equivalent DC voltage developed across the load. 3.the load current. 4.power dissipated by the load. Assume ideal diode characteristics.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
The half-wave rectiﬁer as shown is operating at a frequency of 60Hz, and the rms value of the transformer output voltage vI is 12.6V±10%. What are the nominal and worst case values of the dc output voltage VO if the diode voltage drop is 1V?
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
(a)Derive the average and rms output voltages and currents for three-phase half controlled rectifier with free wheeling diode and RLE load.(b))In a single phase full converter, if output voltage has peak and average values of 325V and 133V respectively, find the firing angle.
(a) Give an application for the use of a Schottky Barrier diode and explain the reverse recovery characteristic in this type of diode. (b) What are the limitations of Schottky Barrier diodes?
Explain the construction and working of the Zener diode, with characteristics curve.
The measured values of the diode at temperature of 288 Kelvin's ,are Vd=1.0v at ld=10A and Vd=1.5V at Id=90KA. Determine the emission coefficient of the diode? (i) Explain clearly, using simple sketches how a signal diode differs from a power diode (ii)State the one disadvantage of three phase half wave uncontrolled rectifier
For the figure shown, determine the (a) load voltage, (b) voltage across resistor R, (c) current flowing in the zener diode, and (d) zener diode power.
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.
Define the main difference between a rectifier diode and a Zener diode? What is their difference in circuit applications?
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
What is the difference between the maximum Zener current and the reverse current for a Zener diode? What does a positive Zener voltage temperature coefficient signify? How can a Zener diode be temperature compensated?