A single-phase load consumes 10 kW at 0.9 power factor lagging from a distributed generation (DG) unit that is rated at 220 V. What are the magnitude and phase angle of the current drawn from the DG? If another single phase load rated at 10 kW and 0.8 leading power factor is connected in parallel to the same DG, what is the magnitude of the current drawn by the load? What is the current drawn from the DG supplying both loads? Give your answers in a polar form.

A single-phase load consumes 10 kW at 0.9 power factor lagging from a distributed generation (DG) unit that is rated at 220 V. What are the magnitude and phase angle of the current drawn from the DG? If another single phase load rated at 10 kW and 0.8 leading power factor is connected in parallel to the same DG, what is the magnitude of the current drawn by the load? What is the current drawn from the DG supplying both loads? Give your answers in a polar form.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.7P

See similar textbooks

Similar questions

Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
A three-phase line, which has an impedance of (2+j4) per phase, feeds two balanced three-phase loads that are connected in parallel. One of the loads is Y-connected with an impedance of (30+j40) per phase, and the other is -connected with an impedance of (60j45) per phase. The line is energized at the sending end from a 60-Hz, three-phase, balanced voltage source of 1203V (rms. line-to-line). Determine (a) the current, real power. and reactive power delivered by the sending-end source: (b) the line-to-line voltage at the load: (C) the current per phase in each load: and (d) the total three-phase real and reactive powers absorbed by each load and by the line. Check that the total three- phase complex power delivered by the source equals the total three-phase power absorbed by the line and loads.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Two balanced loads are connected to a 240-kV rms 50-Hz line. Load 1 draws 30 kW at a power factor of 0.6 lagging, while load 2 draws 45 kVAr at a power factor of 0.8 lagging. Assuming the RYB sequence, determine: (a) the complex, real, and reactive powers absorbed by the combined load, (b) the line currents, and (c) the kVAr rating of the three capacitors ∆-connected in parallel with the load that will raise the power factor to 0.9 lagging and the capacitance of each capacitor. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages
Under balanced operating conditions, consider the 3-phase complex power delivered by the 3-phase source to the 3-phase load. Match the following expressions, those on the left to those on the right. 0) Real power, Py (ii) Reactive power, Qu (ii) Total apparent power Sy (iv) Complex power, Sy (a) (V3 VLL. IL)VA (b) (V3 Vu sng) var (e) (V3 VLL. IL cos ø) W (d) Py +Qy Note that VLL is the rms line-to-line voltage, IL is the ms line current, and o is the power-factor angle.
Draw an impedance diagram for the electric power system shown in Fig. Showing all impedances in per unit on a 100-MVA base. Choose 20 kV as the voltage base for generator. The three-phase power and line-line ratings are given below. CO1 G1: 90 MVA, 20 kV, X= 9% G2: 90 MVA, 18 kV, X= 9% T1: 80 MVA, 20/200 kV, X=16% T2: 80 MVA, 200/20 kV, X = 20% Line: 200 kV, X = 120 Ohm Load: 200 kV, S= 48 MW + j64 MVAr
From the circuit given below, How can I find the value of load Z for the maximum power transfer and the maximum average power transferred?
what is the mutual inductance in ohms (or the mutual inductive reactance ) between the two mutually-coupled inductors? if circuit to the left of load Z is converted into its Thevenin's equivalent, what would be the magnitude of ZTh in ohms? what is the phase angle of ZTh in degrees? what would be the phase angle of VTh in degrees? what would be the magnitude of VTh in volts if E = 120 V?
Consider an ac network with an ideal transformer (with turns ratio of n:1) shown below where ZL=(1+j0) is the load impedance and Zs=(7−j24). Ideal transformer turns ratio n is chosen so that the average power delivered to the load is maximized. Under this scenario, the average power delivered to the load is given by
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
Two impedances Z 1 and Z 2 , when connected separately across a 230 volt, 50 Hz supply consumed 100 watts and 60 watts at power factors of 0.5 lagging and 0.6 leading respectively. If these impedances are connected in parallel across 230 volt, 60 Hz supply, find: (a) total power absorbed and overall power factor; (b) the value of a reactance to be further connected in series with the two to make the overall power factor to be unity.COMPLETE SOLUTION PLEASE
A system has connected load of 120 kW, peak load of 100 kW, base load of 25 kW and average load of 48 kW. The load factor of the consumer is ?