b) Write the two equations where V1(jw) and V2(jw) are as functions of IA(jw) and IB(jw) in the network of Figure.

Q: QUESTION 8 Consider the feedback system illustrated: r(t) s+3 s(s+ 10) Which of the following…

A:

Q: The sacrifice factor of the op-amp is equal to Select one: O a. Aol + Acl O b. 1+ Aol B O c. Aol -…

A: Sacrifice factor : It is defined as the ratio of open loop gain and closed loop gain it can be…

Q: Given the following transfer functions, . • a) State the nature of the step response (underdamped,…

A: The above question is based on the time response of the 2nd order standard transfer function.…

Q: Consider a Gunn diode fabricated using a lightly doped 3.19 μm thick n' layer that is sandwiched…

A: Given,Thickness of the layer, L=3.19 μm.Velocity, v=0.53×105 ms-1.

Q: Design 2 bit synchronous up/down counter x=0 up x=1 down using T flip flop ? note: when i…

A: Determine the number of flip-flops required: A 2-bit counter requires two Flip-Flops. It has 4…

Q: The simplified Sum of Product form of the following Boolean expression: (P+Q+R) (P+Q+R) (P+Q+ R) is

A: It is given that: Y=P+Q¯+RP+Q+RP+Q+R¯

Q: If the circuit is converted to a Norton’s equivalent circuit, what are the values of RN and IN for a…

A: Vth= 20V Rth= 10 ohms

Q: a. Draw the circuit t0 No need to solve it in time domain.

A: For the given circuit the value of initial voltage needs to be calculated and the node equation for…

Q: Given an input voltage from power supply battery, V dc-12V, f=3 kHz and ON time is 0.2ms. Calculate…

A: Given : Vdc=12 Vf=3 kHzTON=0.2 ms

Q: Q5. Find the answer (in mA) to Question 5 in the attached image where: Vi(min) = 14 Volts, Vi(max)…

A: The above is a voltage regulator circuit using a Zener diode and BJT. We need to find the maximum…

Q: Q1) The equivalent low-side parameters of a 250kVA, 4160 – 480V, 60 Hz transformer are Reg.LS…

A: Given,For a low-side transformer,S=250kVAVload=4160 VV=480Vf=60HzReq,LS=0.00920 ΩXeq, LS=0.0433…

Q: 0.5% of its A Wheatstone bridge is employed to measure temperature using a sensor that will exhibit…

A:

Q: Q2)A-A 220-V, three-phase, two-pole, 50-Hz induction motor is running at a slip of 5 percent. Find:…

A:

Q: Referring to the given circuit, what is the power dissipated for the load resistor? VS 30 V R1 220 Ω…

A: here we have to find the power dissipated by the load resistor.

Q: The voltage across a capacitor in a series RC circuit is given by the equation Vc = 250 (1-e25t),…

A: According to given question circuit diagram is given by,

Q: For the network shown in Figure Q4 apply Norton's Theorem to determine the current, 120, flowing…

A: Given Data: A DC circuit with, Resistors  Current source and  Voltage source To Find: Current…

Q: 1)The circuit shown below is initially, for t < 0, with capacitor C connected to a battery (Vbat =…

A: The circuit diagram,

Q: Q1. Find the current through each resistor and voltage drop at each resistor for the networks in…

A:

Q: Find the poles and zeros of the following transfer function. Plot them on the complex plane G(s) =…

A: given here a transfer function and asked to poles and zeros.

Q: Calculate V₁ and V₂ in the circuit shown in Fig. 10.6. Log--Tabo 75/0° V 4 Ω ww ell Figure 10.6 For…

A: For this AC circuit , we need to calculate the node voltage V1 and V2 Circuit:-

Q: Question 1 Find Rab, where each resistance is 3 ohms. a o b ww www ww

A: The circuit diagram,

Q: Problem 1 - In the circuit below, apply source transformations and resistance reductions to simplify…

A: The given circuit diagram is shown below,

Q: (iv) Design Problem: Referring to the circuit of Figure 2.1a, a designer wishes to create three…

A:

Q: 4) Plot the root loci for a system with G (s) = K (s²+2s+2) (s²+2s+5) H(s) = 1

A: Gs = ks2+2s+2s2+2s+5, H(s) =1

Q: Often, pumps and some other electrical equipment are measured in horsepower. It is highly…

A: given  that motor power rating (P) is 10 HP  1HP = 746 Watts motor runs 2.5 hours (t - time) a day…

Q: The following are the impulse responses of LTI systems. Which system is stable? Oh[n] (1.1)" un +1]…

A:

Q: For the circuit attached, A. What resistor connected across all terminals a-b will absorb maximum…

A: given circuit is

Q: Q4: A: Draw only, a distributer (DC ring distributer) ABCDA is fed from point A with 300 v. The main…

A: Step-1-&gt;

Q: In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary…

A: The above question is based on the EMF equation of a transformer.

Q: What is the allowable ampacity of the bike shop front desk's wiring? What is the allowable ampacity…

A: 1. We have given about bike shop Location Conditionn = Well ventilated and normally heated…

Q: i=I sin(t+₁) V = V sin(oot+0 + v) Z

A: v = V sinωt + ϕv = 3458.8 sinωt + 31.7° Vi  =  I  sinωt + ϕi = 208.3 sinωt + 54° A

Q: A 220 V, 1.5 HP, 60 Hz, six pole, capacitor start induction motor has the following main- winding…

A: Given Data: A single-phase capacitor start induction motor with, Stator impedance, R1+jX1=1.2+j1.9…

Q: Suppose L = 30 henrys, R = 50 ohms, C = 1/500 farads, E = 50 volts, q(0) = 4 coulombs, and q'(0) =…

A:

Q: (c) Parallel Resistors Circuit - KCL (i) For the circuit of Figure 2.2a, assume the source-voltage,…

A: supply voltage E = 15 V resistances are  R1 = 3.3 KΩ  R2 = 2.2 KΩ R3 = 1 KΩ measurement of current…

Q: Sv + + UX- 22 + sr Find V₂ and ix ил tm Yv

A:

Q: A 250 V, d.c. shunt motor has an armature resistance of 0.5 ohms and a field resistance of 250 ohms.…

A:

Q: Q5)A- A 3-phase Induction motor has an efficiency of 0.91 when it delivers an Output power of 22KW.…

A: The above question is based on the power flow diagram of a 3-phase induction motor. Please note that…

Q: II. USING KIRCHOFFS VOLTAGE LAW (KVL), FIND THE REQUIRED VOLTAGE AND CURRENT BELOW. a. Find I and…

A: given circuit is                                    current  i = 0.25 A to find resistance R

Q: Complete both the nodal analysis and mesh analysis sections of Table 3.0. Include all calculations…

A:

Q: What is the dynamic resistance (in Ohms) of a diode if its ID = 4.99 mA? No need for a solution.…

A: Diode current is given as,ID=4.99 mA. Thermal voltage is given as, VT=26 mV.

Q: Define thermal runaway in BJTs? Also state the reasons how it can occur in BJTs and the ways to…

A: Define thermal runaway in BJTs? State the reasons how it can occur in BJTS and the ways to avoid it.

Q: (b) Series Resistors Circuit - KVL (i) For the circuit of Figure 2.1a, assume the source-voltage, E…

A: Given Data: Supply voltage E = 15 V Series resistances are, R1= 3.3 kΩ R2= 2.2 kΩ R3= 1  kΩ To…

Q: 7.64 The switch in the circuit in Fig. P7.64 has been in position x for a long time. The initial…

A:

Q: Question 3 Find the maximum power that can be transferred to the load RL in mW unit. бк 1mA( 4000…

A:

Q: Vx www R2 Ω www R1 Ω Click here for image ww Gm Vx R3 Ω R4 Ω Find the current I, shown in the…

A: In this question We need to determine the current I as shown the circuit.  We are solving this…

Q: зл ЗЛ ЗЛ Re в Find 2A Value

A: We need to calculate the value of ZA using wye -delta conversion.

Q: Question 1: Find the line currents Ia, Ib, and Ic in the three-phase network of Fig. 12.53 below.…

A: Given Circuit   Given that: ZY=4+j6 Ohms Z∆=12-j15 Ohms Zl=2 Ohms   To determine: Line current Ia,…

Q: Question 7 For the four-resistor bias circuit shown below, calculate lc (in A) given a value of ß =…

A: Given circuit is  where VCC=12V , R1=20 kΩ , R2=10kΩ , RC=2kΩ , RE=1kΩ , β=157 given here BJT…

Q: Find the value of the capacitance in derivation needed to correct a load of 140 kVAR with 0.85 fp…

A: Initial KVAR rating Q1=140 KVAR. Initial power factor cosϕ1=0.85. Improved power factor cosϕ2=1. RMS…

Q: Find the sum of two sinusoidal voltages, given as follows: V₁ (t)=V1 cos(wt+1) and v₂ (t)=V2…

A: