Answered: A single-phase transformer rated at 55…

A single-phase transformer rated at 55 KVA has no load voltage of 220 volts, when the regulation is 4%. The full load voltage will be V.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4MCQ: An ideal transformer has no real or reactive power loss. (a) True (b) False

See similar textbooks

Related questions

Q: B A 20 kVA, 200V/400V, 50 Hz, single-phase transformer has a secondary terminal voltage of 382.5…

Q: A 33 KV substation is to be connected to a 11 KV stepdown substation which is at a distance of 1.5…

A: We have Transmission line which connects 33 KV Sub-Station to 11 KV Substation. This line is 1.5 KM…

Q: A 500 kVA, 3-phase transformer has iron losses of 300 WV and full load copper losses of 600 W. The…

A: Given values are - S=500kVAIron Loss(PIron)=300WFull load copper lossPCU=600W

Q: A 8 MVA, 138/13.8 KV transformer is connected to an infinite bus. If a bolted three phase fault…

A: Given Transformer impedance X=10 % P=8 MVA Sec voltage of transformer =Vs =13.8 kV

Q: 76. A 200-kVA, 2300/460 V, 60-Hz two-winding transformer is to be used as an autotransformer to…

Q: During routine tests of a three phase transformer, measurements of DC resistance between winding…

A: During Routine tests of Three phase Transformers ,Measurement of DC Resistance between winding…

Q: Calculate the number of turns needed in the secondary winding of a transformer to transform a…

Q: 2. What is unique about the High Voltage Test Transformer?

Q: Explain the Different connections of Three Phase Transformer including the working principle

A: Electrical machines can be either generator, motors or transformers. They can be either Ac machines…

Q: A single-phase transformer rated at 55 KVA has no load voltage of 241 volts, when the regulation is…

Q: A core type transformer operates on 400 / 230 volt, 55 Hz supply. If the cross-sectional area of the…

Q: A 4400 volts 60 Hz transformer has a core loss of 840 watts, of which one-third of which is eddy…

Q: When one transformer is removed from a AA bank of 30 kVA transformer, the capacity of the resulting…

A: we need to find out rating of delta delta transformer when one transformer is removed.

Q: What will be the corresponding CT connection configuration for differential protection scheme, if…

A: Given To determine CT connection configuration for differential scheme, if transformer is connected…

Q: A 11 kVA, 230V/440V, single-phase transformer has a secondary terminal voltage of 390.2 volts when…

A: Vno load=440Vload=390.2Regulation of the transformer=Vno load-VloadVloadx100%

Q: 3 single-phase transformers of 2200/220 Volts each will be combined to form a 3-phase transformer.…

A: The supply can be single phase or three-phase. The loads can also be balanced or unbalanced. The…

Q: When conducting no-load test on a given single-phase transformer, the following test data were…

A: As per the guidelines, we supposed to answer first three part of the question at a time so please…

Q: A single-phase transformer when supplied from 220 V, 50 Hz has eddy current loss of 50 W. If the…

A: we need to find out eddy current loss at 330V.

Q: Detailed description of open circuit test on single phase transformer

A: In this question we discuss about open circuit test of transformer .

Q: If the polarity of one transformer is reversed on a delta bank of single-phase transformers that are…

Q: Q/ A 40-kVA, 3,300/240-V, 50 Hz, 1-phase transformer has 660 turns on the primary. Determine: (a)…

A: Given, A 40-kVA, 3300/240 V. 50 Hz 1-phase transformer, E1E2=3300 V240 V Primary turns, N1= 600

Q: A short circuit test was performed upon a 10-kVA, 2300/230-volt transformer with the following…

A: Short circuit test is performed on high voltage side with low voltage side short circuited. Here…

Q: An open delta three phase transformer system has one transformer center tapped to provide a neutral…

Q: Construct the Equivalent Circuits of Transformer for distribution substation referred to the primary…

Q: Question 1 The shell type transformer has more leakage flux compared to core type transformer True…

A: The leakage flux in core type transformer more than that of shell type transformer .Because the core…

Q: A single phase 200/200 V ,55HZ transformer has an efficiency of 98% at full- load. Determine the…

A: for transformer output frequency = input frequency. and voltage regulation = no load voltage-full…

Q: A 75 kVA, 230/115 volts, single phase transformer was tested with following test results: short…

Q: A 6,900/230-volt transformer is provided with 24, 5, 7%, and 10 per cent taps on the primary side.…

A: It is given that:V1V2=6900230N1N2=30:1

Q: A core type transformer operates on 400 / 225 volt, 55 Hz supply. If the cross-sectional area of the…

Q: In a 1-phase transformer, if the no load secondary terminal voltage is 227 V and the full load…

A: Although formula for voltage regulation is given by %VR=Vno load-Vfull loadVno load×100% Given…

Q: What should be the turns ratio of a 3 phase transformer to transform 10000kVA from 230kV to 4160V if…

A: Given: 3 phase transformer connected in delta to wye VL1=230 kVVL2=4160 V

Q: Given the exciting current of a 20 KVA single phase transformer on a 2,200-volt circuit is 5 percent…

Q: Questions: 1. Why a short circuit test is done on the transformer with LV winding shorted and supply…

Q: A single-phase transformer rated at 55 KVA, has full load voltage of 216 volts, when the regulation…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

A: We have given the equivalent circuit impedance 20kVA ,8000/240Vwith frequency 60Hzwhere open circuit…

Q: What is the per unit impedance of a 50 MVA, 2% impedance transformer if the base is changed to 100…

Q: Why transformer rating in kva

A: According to the question we have to explain why transformer rating in kva.

Q: handwringing

A: Explanation: For welding application, the transformers used are: High reactance type welding…

Q: Calculate the number of turns needed in the secondary winding of a transformer to transform a…

Q: 10. A 6,900/230-volt transformer is provided with 24, 5, 7%, and 10 per cent taps on the primary…

A: The transformer has a voltage rating of 6900/230 V Different taps are provided on the primary side…

Q: A 25kVA, 2400/240, 60Hz single phase transformer gave the following short circuit test result Vsc =…

A: resistance referred to primary side = short circuit power short circuit current2

Q: 6-Writ the procedure of no load test of Single phase transformer and draw the connection diagram of…

Q: A single-phase transformer is rated at 4,200 Volts primary and 420 Volts secondary. It has 2000…

Q: A 16 kVA, 210V/410V, 50Hz, single-phase transformer has a secondary terminal voltage of 362.5 volts…

Q: 1. Draw the equivalent circuit of a single phase transformer (test transformer).

A: The transformer has a primary and a secondary side. It converts electrical power to electrical power…

Q: A core type transformer operates on 415/220 volt, 50 Hz supply. If the cross-sectional area of the…

Q: A 5 KVA, 200V/400 V, single-phase transformer has a secondary terminal voltage of 385.5 volts when…

A: Given data, A single phase transformer has S=5 kVAV1/V2=200V/400VV2fl=385.5 V

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

A single-phase transformer rated at 55 KVA has no
load voltage of 220 volts, when the regulation is 4%.
The full load voltage will be
V.
211.20
110.00
146.67
224.40

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
The leakage reactance of a three-phase, 300-MVA,230Y/23-kV transformer is 0.06 per unit based on its own ratings. The Y winding has a solidly grounded neutral. Draw the per-unit equivalent circuit. Neglect the exciting admittance and assume the American Standard phase shift.
The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) False
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
A 130-MVA,13.2-kV three-phase generator, which has a positive-sequence reactance of 1.5 per unit on the generator base, is connected to a 135-MVA,13.2/115Y-kV step-up transformer with a series impedance of (0.005+10.1) per unit on its own base. (a) Calculate the per-unit generator reactance on the transformer base. (b) The load at the transformer terminals is 15 MW at unity power factor and at 115 kV Choosing the transformer high-side voltage as the reference phasor, draw a phasor diagram for this condition. (C) For the condition of part (b), find the transformer low-side voltage and the generator internal voltage behind its reactance. Also compute the generator output power and power factor.
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
Reconsider Problem 3.64 with the change that now Tb includes both a transformer of the same turns ratio as Ta and a regulating transformer with a 4 phase shift. On the base of Ta, the impedance of the two comp onents of Tb is jO.1 per unit. Determine the complex power in per unit transmitted to the load through each transformer. Comment on how the transformers share the real and reactive pors.
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer at the load end of a 2400-volt feeder whose series impedance is (1.0+j2.0) ohm. The equivalent series impedance of the transformer is (1.0+j2.5) ohms referred to the high-voltage (primary) side. The transformer is delivering rated load at a 0.8 power factor lagging and at a rated secondary voltage. Neglecting the transformer exciting current, determine (a) the voltage at the transformer primary terminals, (b) the voltage at the sending end of the feeder, and (c) the real and reactive power delivered to the sending end of the feeder.